background image

3.5. Battery and charger

Battery description

The 

SOURCETRONIC MPK-102e

 micro-ohmmeter uses a rechargeable

12 V battery. 

Charging procedure:

Check that the 

On/Off

 key is OFF.

Connect the equipment to the mains supply.

The  

Battery   charging

  indicator   (

)   will   keep   on

lightning with a red light up to completing the charge. At that point, it will
change   to   a   green   light,   being   like   this   up   to   the   equipment
disconnection from the mains supply.

Make   sure   that   the   voltage   of   the   mains   supply   is
compatible with the voltage supply of the equipment!

At the end of battery useful life, the battery must be recycled or 
disposed of properly, in order to protect the environment.

The rechargeable battery does not show the “memory effect” and there are no
restrictions to start charging it as many times as is needed. However the battery
could be damaged if remains in deep discharge for a while. 

To avoid this effect, charge the battery before  left the equipment in storage and
don’t let pass more than 30 days without recharge, even if the instrument wasn’t
used (under storage, the battery loses part of its charge).

10

Summary of Contents for 61985






















Reviews: