background image

 

 

 

 

 

 

This symbol indicates the presence of dangerous 
voltage inside the enclosure, sufficient enough to 
cause electric shock. 
 
This symbol indicates the presence of important 
operating and maintenance instructions for the 
device. 
 

 
 

 

Safety, Environmental and Setup Instructions 

 

Use the device in dry indoor environments only. 

 

Protect the device from humidity. 

 

Do not open the device. 

RISK OF ELECTRIC SHOCK!

  Refer opening and servicing to qualified personnel. 

 

Connect this device to a properly installed and earthed wall outlet only. Make sure the mains voltage corresponds with 
the specifications on the rating plate. 

 

Make sure the mains cable stays dry during operation. Do not pinch or damage the mains cable in any way. 

 

A damaged mains cable or plug must immediately be replaced by an authorized service center.  

 

In case of lightning, immediately disconnect the device from the mains supply. 

 

Children should be supervised by parents when using the device. 

 

Clean the device with a dry cloth only. 
Do NOT use CLEANING AGENTS or ABRASIVE CLOTHS! 

 

Do not expose the device to direct sunlight or other heat sources. 

 

Install the device at a location with sufficient ventilation in order to prevent heat accumulation. 

 

Do not cover the ventilation openings! 

 

Install the device at a safe and vibration-free location. 

 

Install  the  device  as  far  away  as  possible  from  computers  and  microwave  units;  otherwise  radio  reception  may  be 
disturbed. 

 

Do  not  open  or  repair  the  enclosure.  It  is  not  safe  to  do  so  and  will  void  your  warranty.  Repairs  only  by  authorized 
service/ customer center. 

 

Only use mercury and cadmium-free batteries. 

 

Used batteries are hazardous waste and NOT to be disposed of with the household waste!!!   
Return the batteries to your dealer or to collection points in your community. 

 

Keep batteries away from children. Children might swallow batteries.  
Contact a physician immediately if a battery was swallowed. 

 

Check your batteries regularly to avoid battery leakage. 

 

Batteries shall not be exposed to excessive heat such as sunshine, fire or the like. 

 

CAUTION: Danger of explosion if battery is incorrectly replaced 

 

Replace only with the same or equivalent type 

 
 
 
 
 
 
 
 

ENVIRONMENTAL PROTECTION

 

Do not dispose of this product with the normal household waste at the end 
of its life cycle. Return it to a collection point for the recycling of electrical 
and  electronic  devices.  This  is  indicated  by  the  symbol  on  the  product, 
user manual or packaging.

 

The materials are reusable according to their markings. By reusing, recycling or 
other  forms  of  utilization  of  old  devices  you  make  an  important  contribution  to 
the protection of our environment.

 

Please contact your local authorities for details about collection points.

 

WARNING

 

Risk of electric shock 

Do not open!

 

Caution: To reduce the risk of electric shock, do not remove the 

cover (or back). There are no user serviceable parts inside. Refer 

servicing to qualified service

 

personnel.

 

Summary of Contents for BT-1308











Reviews: