background image

 

                                                                                                                                                       

English Instruction Manual         

   

                                                                                                                                                                                        8                                               

 

 

3.7  How to Use SLEEP Function 

  When the unit stays on standby mode, using sleep function can terminate LAMP. 
  When the unit turns on, using sleep function can terminate unit and LAMP. 
  Press

Sleep

key to turn on sleep function and the defaulted time is 120 minutes. 

  Press

Sleep

key to adjust sleep time value by five minutes. 

  Pressing and holding

Sleep

key can cancel sleep function. 

  When the sleep time is 5 minutes, press

Sleep

key once again to cancel sleep function.   

3.8  How to Control Backlight 

  Press

Dimmer

key shortly to turn on or off Dimmer function. When it’s powered up, backlight will gets darken 

if no any keys have been pressed. 

3.9  Alarm Wake-Up 

  Press

SNOOZE

key to enter into sleeping mode and the alarm mark will be flashing on LCD display. It will 

wake up alarm again after presetting sleeping time. 

  When unit turns on sleeping mode and stays on standby mode, press 

AL1

to cancel Alarm1 and press     

AL2

to cancel Alarm2. 

  The unit will stop waking up alarm if no any keys have been pressed after waking up alarm within ten 

minutes. 

3.10  SDA Wake-Up 

  When SDA presetting date wakes up press any keys to terminate it. If no keys have been pressed while SDA 

wakes up, it will be waking up at the beginning of next hour and terminating after 22 hours. 

 

 

 

 

 

 

3.11 LED Light 

Press 

LAMP

to turn on or turn off LED light. Press 

light+

  to increase lightness and press 

light-

to decrease lightness, press and hold them to increase or decrease lightness rapidly. 
 

3.12 EU Directive on Eco-Design (ErP) 

When device work with a media source by Bluetooth, it’s should be automatic power off and change to 
standby mode if no signal from sound source for play back over 15 minutes. 
The function not active for Radio... 
 

Summary of Contents for BT-1308











Reviews: