background image

 

 

2

Precautions and safety notes 

 
To reduce the risk of fire or electric shock, do not expose this unit to rain or operate this unit in a wet environment. 
 
Use only the power module supplied with the unit unless you are qualified to use a substitute power supply.  Use of another module or supply 
with incompatible specifications will void the warranty if damage occurs. 
 
If the unit becomes physically damaged due to dropping or for other reasons, it should be returned to the factory for repair to avoid the risk of 
further damage to the unit or to attached units. 
 
To avoid damage due to lightning, the power supply should be unplugged during an electrical storm.     
 
 
 
 
 
 
 

 
 
 
 

Copyright 2002 by Sound Sculpture Musical Instrument Products  
4700 Sterling Drive Ste C - Boulder, Colorado 80301 - USA 
303-442-1954 (fax) 

303-447-3502 

[email protected]     www.soundsculpture.com 
 
This publication may not be reproduced by any means in whole or in part in any form or by any means including electronic except for personal 
use without written consent from an officer of Sound Sculpture Musical Instrument Products. 

Summary of Contents for PowerSwap









Reviews: