Sota SP Lite SPL1 Manual Download Page 7

© 2003-2022 SOTA Instruments Inc. 

Page 7 of 11

|

 www.sota.com

The SP Lite Model SPL1 Manual

hoW miCroPUlsing shoUlD feel

1. the sensation is a gentle pulsing. While the microcurrents should be felt, it is not 

necessary to turn the intensity control up to an uncomfortable level.

2. With repeated use, the ability to feel the microcurrents may change. it may be 

necessary to increase the intensity in order to feel the microcurrents.  

3. 

Twitching of the fingers is normal at a higher intensity.

4. 

During the first weeks of use, the skin may become irritated. Over time, irritation 

usually decreases or disappears. Alternate wrists each session to minimize the 

potential for irritation.

sensitive skin

Some individuals may be particularly sensitive to microcurrents and the irritation may 

continue. To minimize irritation:

1. Use Sponge Sleeves - available from SotA.
2. Wash wrists thoroughly after each session and apply a healing gel or lotion such 

as aloe vera, vitamin e or mSm cream. 

3. micropulse for shorter periods of time until the irritation disappears.
4. Wet the cotton Sleeves with distilled water, ionic~colloidal Silver or conductive 

gel. if unable to feel the current, try a commercial saline solution for the eyes. this 

is gentler than adding salt to the water. 

tyPiCAl Use

Alternate wrists daily.
Length of Session: 

Build up time gradually. it is best to start slowly. Start with 10 to 

20 minutes a day. increase gradually to a minimum of 2 hours each day.

Length of Use: 

the SotA products User guide available at  

www.sota.com/spug offers suggestions for focused, Basic and ongoing Wellness 

plans. 
general guideline: Use daily for a minimum of 8 to 12 weeks. once completed, 

setting a schedule for ongoing use is beneficial. 

Drink Plenty of Water: 

it is important to drink enough water when using the unit. 

Drinking ozonated water is especially helpful.

Summary of Contents for SP Lite SPL1












Reviews: