Sony ZV-1 Service Manual Download Page 82

Page: 82 / 104

Installation

Match the 1st Group Press Block of the 1 Group Frame Block Assy with the cabinet number of the 2nd/3rd group assy and

install the 1 Group Frame Block Assy while turning it clockwise.

•

If Ornamental Ring (A) and Barrier Block Assy is installed to 1 Group Frame Block Assy, remove them first.

•

Be careful not to lose the 1st Group Press Block.

•

When installing the 1 Group Frame Block Assy, stop turning it when the convex parts of the 1st Group Press Block and the
2nd/3rd group assy match.

Install the Straight Tube Block Assy matching its cabinet number with the flexible boards position of the 1st/2nd/ 3rd group assy.

3. After turning the Straight Tube Block Assy counterclockwise about eight degrees to fully install it, turn the Straight Tube Block

Assy clockwise to the maximum extent to fit the bayonet.

Note

1st Group Press Block

2nd/3rd group assy

Cabinet number

1 Group Frame Block Assy

Cabinet number

Straight Tube Block Assy

Flexible boards

1st/2nd/3rd group assy

Gap

Straight Tube Block Assy

About 8

Sony CONFIDENTIAL

For Authorized Servicer

SYS SET

2020/05/28 23:46:49 (GMT+09:00)

Summary of Contents for ZV-1








































































































Search results

Summary of Contents for ZV-1

Reviews:

Related manuals for ZV-1

Brands by name

Popular brands

Sony ZV-1, Service Manual

Search results

Summary of Contents for ZV-1

Reviews:

Related manuals for ZV-1

Brands by name

Popular brands