background image

3 (E)

XDJ-1000

Manual Structure

Purpose of this manual

This manual is the installation manual of Professional Disc Library XDJ-1000 and 
Professional Disc Drive XDBK-J102.
This manual is intended for use by trained system and service engineers, 
and provides the information that is required to install (operating environment, 
installation space, connection information, etc.).
For the installation of the Optional Power Supply XDBK-101, refer to the Installa-
tion Manual supplied with XDBK-101.

Related manuals

Besides this Installation Manual, the following manuals are prepared for this unit.

.

  Operation Manual (PDF) (Supplied with this unit.)

This manual describes the application and operation of this unit.

.

  Maintenance Manual (Available on request)

This manual describes the maintenance and service information (service overview, 
error message, maintenance mode, periodic check, replacement of main parts, de-
tailed parts list, block diagrams, board layouts, schematic diagrams, etc.) for this 
unit.

.

  XDBK-101 Installation Manual (Supplied with XDBK-101)

This manual describes the installation of the Optional Power Supply XDBK-101.

Summary of Contents for XDCAM XDBK-J102





























Reviews: