manualshive.com logo in svg

Sony XCL-U100, Technical Manual

Share
Download
Sony XCL-U100 Technical Manual Download Page 18

Fu
n

c

tio

n

s

3. Camera mode

18

3.2.4.

Trigger mode

This mode is for starting exposure by synchronization 
with the external trigger input (DC IN connector or 
DIGITAL IF connector) and then outputting the 
individual video signals of all pixels after the time that 
was set for the shutter elapses. There is the edge 
detection mode for detecting the rise edge of the external 
trigger signal and the width detection mode for detecting 
the effective period of the trigger. The period of the 
external trigger signal cannot be set shorter than the 
shutter speed. Furthermore, if the shutter is set to OFF, 
frame period (fps) is prioritized and the shutter speed 
will be the reciprocal of the maximum exposure time 
that can be set.
The shutter speed will be 1/15 s in normal mode, 1/30 s 
in binning mode, and 1/15 s to 1/48 s depending on the 
number of lines in partial scan mode. For details on 
partial scan mode, see page 21.
T1 is the maximum exposure time.

T1 > 1253 H
T3 = T2 + 32 H
exposure time 

≤

 T1

* Shutter setting value in edge mode; pulse width in 

width mode.

Edge trigger mode

T1

T3

1 H

1200 H

1600 CL

1

2

1

320 CL

T2*

11

99

1200

When trigger pulse polarity is positive

TRG (width)

FVAL

LVAL

DVAL

TRG (edge)

Video output 
(lines)

1H = 53.333 µs

1 CL = 27.777 ns

Shutter

T1

Trigger width

T2

T3

2 s

2.001 s or more

100 µs or more 2 s or less

2 s

2.002 s

1 s

1.001 s or more

1 s

1.002 s

1/2 s

501 ms or more

500 ms

501.71 ms

1/7.5 s

134 ms or more

133.34 ms

135.05 ms

1/15 s

66.8 ms or more

66.68 ms

68.39 ms

1/30 s

33.34 ms

35.05 ms

1/60 s

16.67 ms

18.38 ms

1/100 s

10.01 ms

11.72 ms

1/120 s

8.33 ms

10.04 ms

1/250 s

4.01 ms

5.72 ms

1/500 s

1.983 ms

3.69 ms

1/1,000 s

1.023 ms

2.73 ms

1/2,000 s

543 µs

2.25 ms

1/5,000 s

223 µs

1.93 ms

1/10,000 s

117 µs

1.83 ms

Summary of Contents for XCL-U100













































Reviews:

No comments

Brands by name

Popular brands

Load more brands