manualshive.com logo in svg

Sony XCL-U100, Technical Manual

Share
Download
Sony XCL-U100 Technical Manual Download Page 21

Fu
n

c

tio

n

s

3. Camera mode

21

3.2.6.

Trigger partial scan mode

In this mode the partial scan action begins through 
synchronization with the external trigger input.

starting position for display 

≤

 32

exposure time 

≤

 T1

T1 = ending position for d 31 + ROUNDUP ((1217 - ending position for display) / 8,0) (H)
Tb = 14 + starting position for display (H)

starting position for display > 32
exposure time 

≤

 T1

T1 = number of lines dis 62 + ROUNDUP ((starting position for display - 32) / 8,0) + ROUNDUP ((1217 - 
ending position for display) / 8,0) (H)
Tb = 62 + ROUNDUP ((starting line for display - 32) / 8,0) (H)

<ROUNDUP functions>

Round up the value for the function, ROUNDUP (x,0) = x, to the nearest whole number.
Example: ROUNDUP (50.0,0) = 50 / ROUNDUP (50.3,0) = 51

In edge mode, T2 will be set to the values on the right 
side of the table when the shutter is set to the values on 
the left side of the table.

In width mode, the shutter will be set to the values on the 
left side of the table when the trigger width is set to the 
values (T2) on the right side of the table. The shutter 
setting is ignored in width mode.

T1

Tb

1 H

320 CL

T2

73

9

740

501 502

501

1600 CL

FVAL

LVAL

DVAL

Video output 
(lines)

TRG

240 H 

(number of lines displayed)

1H = 53.333 µs

1 CL = 27.777 ns

Starting position for display

Ending position for display

When trigger pulse polarity is positive

Shutter

T2

2 s

2 s

1 s

1 s

1/2 s

500 ms

1/7.5 s

133.34 ms

1/15 s

66.68 ms

1/30 s

33.34 ms

1/60 s

16.67 ms

1/100 s

10.01 ms

1/120 s

8.33 ms

1/250 s

4.01 ms

1/500 s

1.983 ms

1/1,000 s

1.023 ms

1/2,000 s

543 µs

1/5,000 s

223 µs

1/10,000 s

117 µs

Summary of Contents for XCL-U100













































Reviews:

No comments

Brands by name

Popular brands

Load more brands