manualshive.com logo in svg

Sony SAL50M28 - 50mm f/2.8 Macro Lens, Service Manual

Share
Download
Sony SAL50M28 - 50mm f/2.8 Macro Lens Service Manual Download Page 24

HELP

SAL50M28 (MACRO 2.8/50) (50mm F2.8 Macro)

HELP20

Grease (G-85):

J-6082-626-A

Adhesive bond (B-40): J-6082-614-A

Apply the grease (G-85) to the instruction part of the linear guide key and apply the adhesive bond (B-40) to the four screws.

HELP21

Adhesive bond (B-40): J-6082-614-A

1.

Set the fixed barrel unit to infinity.

2.

Install the middle tube block so that the notch of the focus cam ring and one of the fixed barrel unit are aligned.

3.

Align the cam groove of the focus ring, one of the fixed barrel unit and the screw hole of the focus cam ring. Then apply the adhesive

bond (B-40) to the guide pin and install the guide roller.

Apply the
adhesive bond (B-40)

Apply the
adhesive
bond (B-40)

Apply the
grease (G-85)

Apply the
grease (G-85)

Guide Roller

Guide Roller

Guide Roller

Middle Tube Block

Fixed Barrel Unit

Screw hole

Notch portion

Notch Portion

Focus Cam Ring

Apply the
adhesive
bond (B-40)

Apply the adhesive bond (B-40)

Apply the adhesiv
 bond (B-40)

Summary of Contents for SAL50M28 - 50mm f/2.8 Macro Lens


































































Reviews:

No comments

Brands by name

Popular brands

Load more brands