Sony PCM-3348HR, Operation Manual

Page: 33 / 256

Chapter 3 Basic Operations
3-7
Chapter 3
4
With the TIMER MODE switch, select CTL
ABSOLUTE, and press the RESET button to set
the tape time display to “00
H
00
MIN
00
SEC
.”
The tape timer display switches momentarily to
“00
H
00
MIN
00
SEC
,” then returns to its previous value.
5
(
1)
Set the switches as follows.
•
TIMER MODE switch: TIME CODE
•
TIME CODE selection switch: INT
•
TIME CODE GEN format selection switch:
Desired format
•
TC GEN switch on the MC board: REC RUN
(2) Holding down the SET button, press the
TIMECODE REC READY button to set the
time code channel to the recording ready state.
The TIME CODE REC READY button lights.
(3)
Press and light the TIME CODE INPUT
button.
(4) Press the RESET button to reset the internal
time code generator to “00
H
00
MIN
00
SEC
.”
Using an external time code
In place of step 5 of the procedure “Using the internal
time code generator,” use the following procedure.
6
Holding down the REC button, press the PLAY
button.
The REC lamps for all channels light, and
recording starts.
The signal level for each channel is displayed on
the respective level meter.
7
When recording is finished, continue recording for
approximately 30 seconds, then press the STOP
button to stop recording.
For simultaneous play while recording
Press the ALL CHANNEL, TIME CODE, A1 or A2
REPRO buttons.
To set the CTL and time code start points to
desired values
In place of pressing the RESET button in step
4
and
5
,
enter a desired time value using the numeric buttons of
the RM-3348HR, then press the
↑
button.
The entered time value is sent to the tape time display
of the PCM-3348HR.
FORMAT
MISMATCH
48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33 CTL A2 A1 TIME
CODE
32 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1
EMPHASIS
MISMATCH
ADVANCE
REC
MASTER
SAFE
EXT CLOCK
ERROR ERROR
REC
REC
READY
AFTER
REC
OVER
–8
–16
–20
0
0 0
–8
–20
–24
–32
–42
–54
SERVO
LOCK
WARNING
SYSTEM
ALARM
ABSOLUTE
TIME CODE
RELATIVE
RESET
RECALL
CUE
STORE
SLOW WIND
A B
A B
A1 A2
ANALOG
MONITOR
ALL CHANNEL SET
AUTO INPUT
TIME CODE
REC
READY
REC
MUTE
REPRO
INPUT
TIMER
MODE
CUE
A B
VARI
SPEED
TAPE TIME
LOCATE
SHUTTLE
º
REW
‚
FF
·
PLAY
π
STOP
®
REC
EDIT
STOP
ZERO
LOCATE
LOCATE TIME
H MIN SEC
H MIN SEC
REC
REC
READY
OVER
–8
–16
–20
–24
–32
–42
–54
REC
REC
READY
OVER
–8
–16
–20
–24
–32
–42
–54
REC
REC
READY
OVER
–8
–16
–20
–24
–32
–42
–54
REC
MODE
MASTER
SAFE
ON
OFF
WORD
LENGTH
INPUT SELECT TIME CODE
READER GEN 2CH-DIO
INSERT 24BIT 44.056kHz OFF ANALOG SDIF-2 ON INT X'tal
NORM
30/29(NDF) 30 INT LCL/REMOTE
44.1kHz INDIVI DIGITAL MADI OFF EXT 29(DF) 29(NDF)
29(DF)
EXT REMOTE 2
48kHz ON INDIVI DI 25
25 AUTO REMOTE 3
VIDEO
24
24
REGENE
(EXT)
1,3,4
16BIT
ASSEM
-BLE
SYNC
REC
SYSTEM
CONTROL SYNC CLOCK EMPH Fs
(1)(2) (3)
(4)
External time code operation
(Continued)