Sony PCM-3348HR, Operation Manual

Page: 32 / 256

3-6
Chapter 3 Basic Operations
Chapter 3
3-4-1 What Is Advance Recording?
3-4-2 Basic Advance Recording
Use the following procedure to carry out advance
recording.
Advance recording operation
3-4 Advance Recording
Regardless of any existing signals recorded on the
tape, the CTL signal, time code signal and digital
audio signals are recorded simultaneously.
This mode is used for live recording.
Simultaneous monitor output for the recorded signal
(simultaneous recording and playback) is possible.
3
Holding down the SET button, press the ALL
CHANNEL REC READY button to set all digital
audio channels to the recording ready state.
If you wish to record on analog audio channels A1
and A2, holding down the SET button, press the
A1 A2 REC READY button to set channels A1
and A2 to the recording ready state.
The ALL CHANNEL REC READY button lights
(and the A1 A2 REC READY button lights).
Note
Normally, simultaneous recording and playback is
only possible during advance recording. However,
certain settings on the MC board can enable
simultaneous recording and playback for recording on
a prestriped tape.
For internal settings of the board, see “MC board” (page A-
20) in Appendixes, “Location of Parts and Controls.”
FORMAT
MISMATCH
48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33 CTL A2 A1
TIME
CODE
32 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1
EMPHASIS
MISMATCH
ADVANCE
REC
MASTER
SAFE
EXT CLOCK
ERROR
ERROR
REC
REC
READY
AFTER
REC
OVER
–8
–16
–20
0
0 0
–8
–20
–24
–32
–42
–54
SERVO
LOCK
WARNING
SYSTEM
ALARM
ABSOLUTE
TIME CODE
RELATIVE
RESET
RECALL
CUE
STORE
SLOW WIND
A B
A B
A1 A2
ANALOG
MONITOR
ALL CHANNEL SET
AUTO INPUT
TIME CODE
REC
READY
REC
MUTE
REPRO
INPUT
TIMER
MODE
CUE
A B
VARI
SPEED
TAPE TIME
LOCATE
SHUTTLE
º
REW
‚
FF
·
PLAY
π
STOP
®
REC
EDIT
STOP
ZERO
LOCATE
LOCATE TIME
H MIN SEC
H MIN SEC
REC
REC
READY
OVER
–8
–16
–20
–24
–32
–42
–54
REC
REC
READY
OVER
–8
–16
–20
–24
–32
–42
–54
REC
REC
READY
OVER
–8
–16
–20
–24
–32
–42
–54
REC
MODE
MASTER
SAFE
ON
OFF
WORD
LENGTH
INPUT SELECT TIME CODE
READER GEN 2CH-DIO
INSERT 24BIT 44.056kHz OFF ANALOG SDIF-2 ON INT X'tal
NORM
30/29(NDF) 30 INT LCL/REMOTE
44.1kHz INDIVI DIGITAL MADI OFF EXT 29(DF) 29(NDF)
29(DF)
EXT REMOTE 2
48kHz ON INDIVI DI 25
25 AUTO REMOTE 3
VIDEO
24
24
REGENE
(EXT)
1,3,4
16BIT ASSEM
-BLE
SYNC
REC
SYSTEM
CONTROL SYNC CLOCK EMPH Fs
1
OFF
12
3
4
ON
OUTPUT
TC GEN
TIME CODE
TEST
MC
NORM ADV
PB TC GAIN
NORM LOW
REC
RUN FREE
RUN
SELECT
BACK UP
2 AUTO REC
3 MESSAGE
4 VARI SYNC
5
(2)
3 2
1
5
(4)
5
(1)
5
(3)
4
6
7
5
(1)
MC board
REPRO
buttons
Using the internal time code generator
1
Set the switches as follows.
•
MASTER SAFE switch: OFF
• WORD LENGTH switch: Word length being used
•
Fs switch: Sampling frequency being used
•
EMPH switch: ON or OFF
2
Set the REC MODE switch on the system control
panel to ADVANCE REC.