Sony PAL NTSC 4.43 SLV-SE80UX Operating Instructions Manual Download Page 53

Page: 53 / 80

Additional Operations

To stop recording

To stop the VCR while recording, press

STOP.

To use the VCR after setting the timer

To use the VCR before a timer recording begins, just press

. The

indicator turns off and the VCR switches on. Remember to press

reset the VCR after using the VCR.

Tips

• The programme is recorded in the current tape speed mode. To change the tape

speed, press SP/LP before you complete the setting in step 7.

• To check, change, or cancel the programme setting, see “Checking/changing/

cancelling timer settings” (page 55).

Notes

• The

indicator flashes in the display window when you complete the setting in

step 7 with no tape inserted.

• If eight programmes have already been set, “FULL” appears in the display window

for about three seconds in step 1.

Press DIAL TIMER to complete the setting.

“OK” appears in the display window for about five seconds.

The

indicator appears in the display window and the VCR stands by

for recording.

Summary of Contents for PAL NTSC 4.43 SLV-SE80UX

















































































Search results

Summary of Contents for PAL NTSC 4.43 SLV-SE80UX

Reviews:

Related manuals for PAL NTSC 4.43 SLV-SE80UX

Brands by name

Popular brands

Sony PAL NTSC 4.43 SLV-SE80UX, Operating Instructions Manual

Search results

Summary of Contents for PAL NTSC 4.43 SLV-SE80UX

Reviews:

Related manuals for PAL NTSC 4.43 SLV-SE80UX

Brands by name

Popular brands