Sony PAL NTSC 4.43 SLV-SE80UX Operating Instructions Manual Download Page 52

Page: 52 / 80

Additional Operations

Recording TV programmes using Dial Timer (continued)

Press DIAL TIMER.

“STOP” and the recording stop time appear alternately in the display
window.

Turn DIAL TIMER to set the recording stop time.

The time changes in 15 minute intervals.

Press DIAL TIMER.

“PROG” and the programme position appear alternately in the display
window.

Turn DIAL TIMER to set the programme position.

To record from a decoder or other source connected to the LINE-1 (TV)
connector, the LINE-2 IN jacks, or the LINE-3 IN (Scart) connector,
press INPUT SELECT to display “L1,” “L2,” or “L3.”

VIDEO

OPC

VIDEO

OPC

VIDEO

OPC

VIDEO

OPC

VIDEO

OPC

VIDEO

OPC

Summary of Contents for PAL NTSC 4.43 SLV-SE80UX

















































































Search results

Summary of Contents for PAL NTSC 4.43 SLV-SE80UX

Reviews:

Related manuals for PAL NTSC 4.43 SLV-SE80UX

Brands by name

Popular brands

Sony PAL NTSC 4.43 SLV-SE80UX, Operating Instructions Manual

Search results

Summary of Contents for PAL NTSC 4.43 SLV-SE80UX

Reviews:

Related manuals for PAL NTSC 4.43 SLV-SE80UX

Brands by name

Popular brands