Sony PAL NTSC 4.43 SLV-SE80UX Operating Instructions Manual Download Page 15

Page: 15 / 80

Getting Started

Getting Started

Step 5

Tuning your TV to the VCR

If you have connected the VCR to your TV using the EURO-AV cable,
skip this step.

RF CHANNEL

Press RF CHANNEL on the VCR lightly.

The factory-preset RF channel appears in the display window.

The VCR signal is output through this channel to the TV.

Turn on your TV and select a programme position for the VCR
picture.

This programme position will now be referred to as the video
channel.

Tune the TV to the same channel as that
shown in the display window so that
the picture on the right appears clearly
on the TV screen.

Refer to your TV manual for tuning
instructions.

If the picture does not appear clearly,
see “To obtain a clear picture from the
VCR” below.

RF CHANNEL

SONY VIDEO CASSETTE RECORDER

continued

Summary of Contents for PAL NTSC 4.43 SLV-SE80UX

















































































Search results

Summary of Contents for PAL NTSC 4.43 SLV-SE80UX

Reviews:

Related manuals for PAL NTSC 4.43 SLV-SE80UX

Brands by name

Popular brands

Sony PAL NTSC 4.43 SLV-SE80UX, Operating Instructions Manual

Search results

Summary of Contents for PAL NTSC 4.43 SLV-SE80UX

Reviews:

Related manuals for PAL NTSC 4.43 SLV-SE80UX

Brands by name

Popular brands