18
1) Only 3D-Dual Stream is supported.
2) 2-sample interleave division
3) Square division
4) SQ will be converted to 2-SI on the sender side.
Notes
If the video formats on the sender side and receiver
side are not properly configured, video cannot be
transmitted.
During 3G-SDI mapping Level B input, signals will be
converted to Level A for output. During Level B-DS
input, signals will be output unchanged as Level B-DS.
Switch number [7] of DIP switch 1 is disabled on units
operating in receiver mode. The 4K video (4096×2160,
3840×2160) output will be fixed at 2-SI on such units.
Downconvert Output Settings
Specify whether to output the video input on the receiver
side in its original format, or whether to downconvert its
resolution for output. By configuring the downconvert
output setting, you can convert the resolution of 4K
video outputs from modality devices and output them
on HD monitors. This allows you to add HD monitors to
a 4K video transmission system.
1) The resolution is converted as follows.
3840×2160: Outputs with the height and width reduced to
1/2.
4096×2160: Deletes 128 dots from the left and right
(3840×2160), and outputs with the height and width reduced
to 1/2.
Network Settings
Video transmission groups
Configure groups for the senders that will transmit
images and the receivers. A single sender can be grouped
with multiple receivers. When groups are configured on
a unit operating in sender mode, IP addresses are
automatically assigned to the unit’s MAIN and SUB
network connectors.
Receiver IP address
Assign IP addresses to the receiver’s MAIN and SUB
network connectors. You can assign addresses regardless
of video transmission groups. Be sure to assign addresses
that are unique from other devices on the network. You
can configure IP addresses via the ON/OFF settings of
switch numbers [5] to [8] of DIP switch 2. For details, see
“DIP Switch Settings” (page 30).
Input video
format
3G-SDI
mapping
4K
format
DIP switch 1
[3]
[4]
[5]
[6]
[7]
1920×1080
/50i
–
–
OFF
OFF
OFF
–
–
1920×1080
/59.94i
–
ON
1920×1080
/50p
Level A/B
ON
OFF
OFF
1920×1080
/50i
Level B-
DS
1)
ON
1920×1080
/59.94p
Level A/B
ON
OFF
1920×1080
/59.94i
Level B-
DS
1)
ON
3840×2160
/50p
Level A/B
2-SI
2)
ON
OFF
OFF
–
OFF
SQ
3) 4)
ON
3840×2160
/59.94p
Level A/B
2-SI
2)
ON
OFF
SQ
3) 4)
ON
4096×2160
/50p
Level A/B
2-SI
2)
ON
OFF
OFF
SQ
3) 4)
ON
4096×2160
/59.94p
Level A/B
2-SI
2)
ON
OFF
SQ
3) 4)
ON
Input video
resolution
DIP switch 1
Output video resolution
[8]
1920×1080
OFF
Same as input video resolution
ON
3840×2160
OFF
ON
Resolution converted
1)
(1920×1080)
4096×2160
OFF
Same as input video resolution
ON
Resolution converted
1)
(1920×1080)
DIP switch 2
Video
transmission
groups
Sender IP
address (MAIN
network
connector)
Sender IP
address (SUB
network
connector)
[2]
[3]
OFF
OFF
Group 0
192.168.10.32
192.168.11.32
ON
Group 1
192.168.10.33
192.168.11.33
ON
OFF
Group 2
192.168.10.34
192.168.11.34
ON
Group 3
192.168.10.35
192.168.11.35
Network connector
(receiver)
Acceptable IP address range
MAIN
192.168.10.100 to 192.168.10.115
SUB
192.168.11.100 to 192.168.11.115
