MEX-XB100BT
20
To capture your voice during handsfree calling, you
need to install the microphone
ʚ
.
Cautions
ˎ
It is extremely dangerous if the cord becomes
wound around the steering column or gearstick.
Be sure to keep it and other parts from interfering
with your driving operations.
ˎ
If airbags or any other shock-absorbing
equipment is in your car, contact the store where
you purchased this unit, or the car dealer, before
installation.
Note
Before attaching the double-sided tape
ʛ
, clean the
surface of the dashboard with a dry cloth.
1
To enable the wired remote control, set
[SET STR CONTROL] in [SET STEERING] to
[EXTERNAL] (page 17).
Installing the microphone
Using the wired remote control
ʛ
ʚ
Clip (not supplied)
ʚ
.
Subwoofer Easy Connection
You can use a subwoofer without a power amplifier
when it is connected to a rear speaker cord.
Notes
ˎ
Preparation of the rear speaker cords is required.
ˎ
Use a subwoofer with an impedance of 4 to 8 ohms,
and with adequate power handling capacities to
avoid damage.
Memory hold connection
When the yellow power supply lead is connected,
power will always be supplied to the memory
circuit even when the ignition switch is turned off.
Front speaker
Subwoofer
Speaker connection
ˎ
Before connecting the speakers, turn the unit off.
ˎ
Use speakers with an impedance of 4 to 8 ohms,
and with adequate power handling capacities to
avoid damage.
Common connection
When the positions of the red and yellow
leads are inverted
When the car without ACC position
After matching the connections and switching
power supply leads correctly, connect the unit to
the car’s power supply. If you have any questions
and problems connecting your unit that are not
covered in this manual, consult the car dealer.
12
continuous power
supply
Yellow
15
switched power supply
Red
12
switched power supply Yellow
15
continuous power
supply
Red
Red
Red
Yellow
Yellow
Red
Red
Yellow
Yellow
Red
Red
Yellow
Yellow
Make sure your car’s auxiliary power connector, and
match the connections of cords correctly
depending on the car.
Power connection diagram
Auxiliary power connector
Installation
Before installing the unit, remove the protection
collar
ͨ
and the bracket
ʓ
from the unit.
1
Pinch both edges of the protection collar
ͨ
, then pull it out.
2
Insert both release keys
ͧ
until they
click, and pull down the bracket
ʓ
, then
pull up the unit to separate.
Removing the protection collar and the
bracket
ͨ
ʓ
ͧ
Face the hook inwards.
2
Mount the unit onto the bracket
ʓ
, then
attach the protection collar
ͨ
.
ʓ
ͨ
ͩ
ͪ
Before installing, make sure the catches on both
sides of the bracket
ʓ
are bent inwards 2 mm (
3
/
32
in).
1
Position the bracket
ʓ
inside the
dashboard, then bend the claws outward
for a tight fit.
Mounting the unit in the dashboard
ʓ
182 mm (7
1
/
4
in)
53 mm (2
1
/
8
in)
Catch
When replacing the fuse, be sure to use one
matching the amperage rating stated on the
original fuse. If the fuse blows, check the power
connection and replace the fuse. If the fuse blows
again after replacement, there may be an internal
malfunction. In such a case, consult your nearest
Sony dealer.
Note
Use an appropriate tool to replace a fuse.
Fuse replacement
Fuse (15 A)
Notes
ˎ
If the catches are straight or bent outwards, the unit
will not be installed securely and may spring out.
ˎ
Make sure the 4 catches on the protection collar
ͨ
are properly engaged in the slots of the unit.
CAUTION
Do not touch the left side of the unit when
removing from the dashboard. The heatsink on
the left side of the unit remains hot right after
use.
Summary of Contents for MEX-XB100BT
Page 16: ...MEX XB100BT 16 MEMO ...
Page 67: ...MEMO MEX XB100BT 67 ...