MEX-XB100BT
18
.
Speaker connection
ˎ
Before connecting the speakers, turn the unit off.
ˎ
Use speakers with an impedance of 4 to 8 ohms,
and with adequate power handling capacities to
avoid damage.
Installation
Before installing the unit, remove the protection
collar
ͨ
and the bracket
ʓ
from the unit.
1
Pinch both edges of the protection collar
ͨ
, then pull it out.
2
Insert both release keys
ͧ
until they
click, and pull down the bracket
ʓ
, then
pull up the unit to separate.
Removing the protection collar and the
bracket
ͨ
ʓ
ͧ
Face the hook inwards.
To capture your voice during handsfree calling, you
need to install the microphone
ʙ
.
Installing the microphone
ʚ
ʙ
Clip (not supplied)
ʙ
When using the steering wheel remote
control
Installation of the connection cable RC-SR1 (not
supplied) is required before use.
1
To enable the steering wheel remote control, select
[SET STEERING]
q
[SET STR EDIT] to make the
registration (page 19).
When the registration completes, the steering wheel
remote control becomes available.
Notes on installing the connection cable RC-SR1 (not
supplied)
ˎ
Refer to the support sites on the back cover for
details, then connect each lead properly to the
appropriate leads. Making an improper connection
may damage the unit.
ˎ
Consulting the dealer or an experienced technician
for help is recommended.
Using the wired remote control
When using the wired remote control
1
To enable the wired remote control, set [SET STR
CONTROL] in [SET STEERING] to [EXTERNAL]
.
.
Mounting the unit in a Japanese car
You may not be able to install this unit in some
makes of Japanese cars. In such a case, consult your
Sony dealer.
TOYOTA
NISSAN
Note
To prevent malfunction, install only with the supplied
screws
ʖ
.
ʖ
to dashboard/center console
Existing parts supplied with
your car
ʖ
Bracket
Bracket
ʖ
to dashboard/center console
Existing parts supplied with
your car
ʖ
Bracket
Bracket
Before installing, make sure the catches on both
sides of the bracket
ʓ
are bent inwards 2 mm (
3
/
32
in). When mounting in a Japanese car, see
“Mounting the unit in a Japanese car” (page 36).
1
Position the bracket
ʓ
inside the
dashboard, then bend the claws outward
for a tight fit.
2
Mount the unit onto the bracket
ʓ
, then
attach the protection collar
ͨ
.
Notes
ˎ
If the catches are straight or bent outwards, the unit
will not be installed securely and may spring out.
ˎ
Make sure the 4 catches on the protection collar
ͨ
are properly engaged in the slots of the unit.
Mounting the unit in the dashboard
CAUTION
Do not touch the left side of the unit when
removing from the dashboard. The heatsink on
the left side of the unit remains hot right after
use.
ʓ
182 mm (7
1
/
4
in)
53 mm (2
1
/
8
in)
Catch
ʓ
ͨ
When replacing the fuse, be sure to use one
matching the amperage rating stated on the
original fuse. If the fuse blows, check the power
connection and replace the fuse. If the fuse blows
again after replacement, there may be an internal
malfunction. In such a case, consult your nearest
Sony dealer.
Note
Use an appropriate tool to replace a fuse.
Fuse replacement
Fuse (15 A)
Cautions
ˎ
It is extremely dangerous if the cord becomes
wound around the steering column or gearstick.
Be sure to keep it and other parts from interfering
with your driving operations.
ˎ
If airbags or any other shock-absorbing
equipment is in your car, contact the store where
you purchased this unit, or the car dealer, before
installation.
Note
Before attaching the double-sided tape
ʚ
, clean the
surface of the dashboard with a dry cloth.
.
Summary of Contents for MEX-XB100BT
Page 16: ...MEX XB100BT 16 MEMO ...
Page 67: ...MEMO MEX XB100BT 67 ...
