Sony MDS-SE9 Service Manual Download Page 67

Page: 67 / 77

MDS-SE9

Ref. No.

Part No.

Description

Remarks

Ref. No.

Part No.

Description

Remarks

MD mechanism deck section-2
(MDM-7S2D)

158

157

156

152

151

170

157

152

161

162

160

159

163

164

165

166

169

168

167

155

153

154

not supplied

not

supplied

not

supplied

151

4-996-267-01 BASE (BU-D)

152

4-231-319-01 SCREW (2X6) CZN, +B (P) TRI

153

4-226-994-01 GUIDE (L)

154

A-4735-075-B HOLDER ASSY

155

X-4952-665-1 SPRING (SHT) ASSY, LEAF

156

4-227-002-01 GEAR, PULLEY

157

3-372-761-01 SCREW (M1.7), TAPPING

158

4-227-025-01 BELT (LOADING)

159

A-4680-638-A LOCK (HOLDER)

160

4-229-533-02 SPRING (STOPPER), TORSION

161

4-227-012-01 SPRING (HOLDER), TENSION

162

A-4680-638-B RETAINER COMPLETE ASSY

163

4-226-995-01 SLIDER (EJ)

164

4-227-013-01 SPRING (EJ), TENSION

165

4-226-996-01 LIMITTER (EJ)

166

4-226-997-04 SLIDER

167

4-226-998-01 LEVER (CHG)

168

4-227-007-01 GEAR (SB)

169

4-227-006-01 GEAR (SA)

170

4-226-999-01 LEVER (HEAD)

7-685-850-04 SCREW +BVTT 2X3 (S)

8-4. MD MECHANISM DECK SECTION-1 (MDM-7S2D)

Summary of Contents for MDS-SE9














































































Search results

Summary of Contents for MDS-SE9

Reviews:

Related manuals for MDS-SE9

Brands by name

Popular brands

Sony MDS-SE9, Service Manual

Search results

Summary of Contents for MDS-SE9

Reviews:

Related manuals for MDS-SE9

Brands by name

Popular brands