Sony MB-806A, Service Manual

Page: 43 / 82

3-17 MB-806A (CE)
WRU-806A (CE, AU)
Step 2: Tuner
[2]
to Tuner
[6]
checking
When the WRU-806A Tuner Unit is installed in the Tuner
[2]
(Tuner unit 2) to Tuner
[6]
(Tuner unit 6) of the MB-
806A, perform the adjustments from procedures (1) to (5)
of “Step 1. Tuner
[1]
(Tuner unit 1) checking” on the
respective tuner units that are installed in the MB-806A.
When performing the above described checking change the
following details as shown below, of the “Step 1. Tuner
[1]
(Tuner unit 1) checking”.
Tuner
[1]
→
Tuner
[2]
,
[3]
,
[4]
,
[5]
, and
[6]
10. DC +9 V OUT voltage check
Equipment and Tools
. DC voltmeter (digital multi meter)
. Metal film resistor 91 Z 2W (Part No. 1-214-609-00)
Procedure
(1) Connect the DC voltmeter to the ANTENNA A IN/DC
9 V OUT connector with 91 Z resistor as shown figure
below.
(2) Check that DC output voltage of ANTENNA A IN/DC
9 V OUT connector is + 8.6
±
0.6 Vdc.
(3) Connect the DC voltmeter to the ANTENNA B IN/DC
9 V OUT connector with 91
Z
resistor.
(4) Check that DC output voltage of ANTENNA B IN/DC
9 V OUT connector is + 8.6
±
0.6 Vdc.
+
_
DC voltmeter
91 Z
2 W
BNC connector
Shield
ANTENNA
A IN
ANTENNA
B IN
MB-806A
9. Tone squelch check
Procedure
Step 1:
Tuner
[1]
(Tuner unit 1) checking
n
The checking procedures describe that the WRU-806A (to
be adjusted) is installed into the Tuner
[1]
slot on the MB-
806A.
(1) Set the MB-806A as follows;
Front panel (Tuner
[1]
)
Channel setting:
CE62 model; Group 00, 6301 channel (806.125 MHz)
CE69 model; Group 00, 6933 channel (858.125 MHz)
AU66 model; Group00, 6701 channel (799.250 MHz)
Muting: ON (Normal mode)
Rear panel
ATT (ANTENNA A, B) switch: 0 dB
(2) Connect the signal generator to the ANTENNA A IN
connector with DC cut fixture.
(3) Set the signal generator as follows:
Signal generator setting
FREQUENCY(carrier frequency):
CE62 model; 806.125 MHz
CE69 model; 858.125 MHz
AU66 model; 799.250 MHz
RF OUTPUT (Output level): 60 dB
u
V
EMF
(= _ 53 dBm)
MODULATION (Modulation frequency):
32.768 kHz
(32.768 kHz must be set
by connecting Function
generator)
DEVIATION (Frequency deviation):
±
1.4 kHz
(4) Turn on and off the MODULATION (modulation
frequency) of the signal generator as follows, and the
LCD indicator (Tuner
[1]
) changes also as follows.
MODULATION ON/OFF LCD indication of Tuner
[1] [1]
[1] [1] [1]
on signal generator
ON GP/CH indication (LCD):
CE62 model; “00. 6301” appears.
CE69 model; “00. 6933” appears.
AU66 model; “00. 6701” appears.
OFF GP/CH indication (LCD):
“NO TONE” appears.
(5) Connect the signal generator to the ANTENNA B IN
connector with DC cut fixture, and perform the
procedures (3) and (4) above.