background image

HT-X9000F/XF9000

2

NOTES  ON  CHIP  COMPONENT  REPLACEMENT

•  Never reuse a disconnected chip component.
•  Notice that the minus side of a tantalum capacitor may be dam-

aged by heat.

SAFETY  CHECK-OUT

After correcting the original service problem, perform the follow-
ing safety check before releasing the set to the customer:
Check the antenna terminals, metal trim, “metallized” knobs, 
screws, and all other exposed metal parts for AC leakage.
Check leakage as described below.

LEAKAGE  TEST

The AC leakage from any exposed metal part to earth ground and 
from all exposed metal parts to any exposed metal part having a 
return to chassis, must not exceed 0.5 mA (500 microamperes.). 
Leakage current can be measured by any one of three methods.
1.  A commercial leakage tester, such as the Simpson 229 or RCA 

WT-540A. Follow the manufacturers’ instructions to use these 
instruments.

2.  A battery-operated AC milliammeter. The Data Precision 245 

digital multimeter is suitable for this job.

3.  Measuring the voltage drop across a resistor by means of a 

VOM or battery-operated AC voltmeter. The “limit” indication 
is 0.75 V, so analog meters must have an accurate low-voltage 
scale. The Simpson 250 and Sanwa SH-63Trd are examples 
of a passive VOM that is suitable. Nearly all battery operated 
digital multimeters that have a 2 V AC range are suitable. (See 
Fig. A)

1.5 k

Ω

0.15 

μ

F

AC

voltmeter

(0.75 V)

To Exposed Metal

Parts on Set

Earth Ground

Fig. A.  Using an AC voltmeter to check AC leakage.

SAFETY-RELATED  COMPONENT  WARNING!

COMPONENTS  IDENTIFIED  BY  MARK  

0

  OR  DOTTED  LINE  

WITH  MARK  

0

  ON  THE  SCHEMATIC  DIAGRAMS  AND  IN  

THE  PARTS  LIST  ARE  CRITICAL  TO  SAFE  OPERATION.
REPLACE  THESE  COMPONENTS  WITH  SONY  PARTS 

 

WHOSE  PART  NUMBERS  APPEAR  AS  SHOWN  IN  THIS  
MANUAL  OR  IN  SUPPLEMENTS  PUBLISHED  BY  SONY.

ATTENTION  AU  COMPOSANT  AYANT  RAPPORT  

À  LA  SÉCURITÉ!

LES  COMPOSANTS  IDENTIFIÉS  PAR  UNE  MARQUE  

0

  SUR  

LES  DIAGRAMMES  SCHÉMATIQUES  ET  LA  LISTE  DES  
PIÈCES  SONT  CRITIQUES  POUR  LA  SÉCURITÉ  DE  FONC-
TIONNEMENT.  NE  REMPLACER  CES  COMPOSANTS  QUE  
PAR  DES  PIÈCES  SONY  DONT  LES  NUMÉROS  SONT  DON-
NÉS  DANS  CE  MANUEL  OU  DANS  LES  SUPPLÉMENTS  
PUBLIÉS  PAR  SONY.

This system incorporates Dolby* Digital 
and the DTS** Digital Surround System.

*Manufactured under license from Dolby 

Laboratories. Dolby, Dolby Audio, Dolby 
Atmos, Dolby Vision, and the double-D 
symbol are trademarks of Dolby 
Laboratories.

**For DTS patents, see http://

patents.dts.com. Manufactured under 
license from DTS, Inc. DTS, the Symbol, 
DTS and the Symbol together, DTS:X, and 
the DTS:X logo are registered trademarks 
and/or trademarks of DTS, Inc. in the 
United States and/or other countries. © 
DTS, Inc. All Rights Reserved.

The BLUETOOTH

®

 word mark and logos are 

registered trademarks owned by Bluetooth 
SIG, Inc. and any use of such marks by Sony 
Corporation is under license. Other 
trademarks and trade names are those of 
their respective owners.

This system incorporates High-Definition 
Multimedia Interface (HDMI™) technology. 
The terms HDMI and HDMI High-Definition 
Multimedia Interface, and the HDMI Logo 
are trademarks or registered trademarks of 
HDMI Licensing Administrator, Inc. in the 
United States and other countries.

“BRAVIA” logo is a trademark of Sony 
Corporation.

“Cle” is a trademark of Sony 
Corporation.

WALKMAN® and WALKMAN® logo are 
registered trademarks of Sony 
Corporation.

“PlayStation” is a registered trademark or 
trademark of Sony Interactive 
Entertainment Inc.

MPEG Layer-3 audio coding technology 
and patents licensed from Fraunhofer IIS 
and Thomson.

Windows Media is either a registered 
trademark or trademark of Microsoft 
Corporation in the United States and/or 
other countries.
This product is protected by certain 
intellectual property rights of Microsoft 
Corporation. Use or distribution of such 
technology outside of this product is 
prohibited without a license from Microsoft 
or an authorized Microsoft subsidiary.

“DSEE” is a trademark of Sony Corporation.

“TRILUMINOS” and “TRILUMINOS” logo are 
a registered trademark of Sony 
Corporation.

All other trademarks are trademarks of 
their respective owners.

Copyrights and Trademarks

Summary of Contents for HT-X9000F





























































Reviews: