6-47
DCR-PC350/PC350E
3-1-2.
Precautions on Adjusting
Note1:
Before performing the adjustments, check the data of page: 0,
address: 10 is “00”. If not, set data: 00 to this address.
1)
The adjustments of this unit are performed in the VTR mode
(PLAY/EDIT mode) or camera mode (CAMERA-TAPE mode).
To set to the VTR mode, set the mode switch to “PLAY/EDIT”
or set the “Forced VTR Power ON mode” using the adjusting
remote commander (Note2).
To set to the camera mode, set the mode switch to “CAMERA-
TAPE” or set the “Forced Camera Power ON mode” using the
adjusting remote commander (Note3).
After completing adjustments, be sure to exit the “Forced VTR
Power ON Mode” or “Forced Camera Power ON Mode”.
(Note5)
2)
The cabinet (top) block (Microphone unit, intelligent accessory
shoe) need not be connected. To remove it, disconnect the
following connectors.
SE-151 board CN2502 (10P, 0.5mm)
SE-151 board CN2504 (4P, 0.8mm)
3)
The cabinet (R) block (LCD panel, touch panel, PD-225 board,
VP-060 board, CR-048 board) need not be connected except
for the CR-048 board. (Use the adjustment remote commander,
to operate the VTR block.) To remove the cabinet (R) block,
disconnect the following connectors.
VC-370 board CN1002 (60P, 0.4mm)
VC-370 board CN1006 (40P, 0.4mm)
As the DC IN jack is attached to the CR-048 board of the cabinet
(R) block, the CR-048 board must be connected to the VC-370
board. So remove the CR-048 board from the cabinet (R). And
connect it to the following connector of VC-370 board.
VC-370 board CN1002 (60P, 0.4mm)
4)
The lens block (Lens device, CD-537 board, ST-108 board)
need not be connected except for the CD-537 board. To remove
the lens block, disconnect the following connectors.
VC-370 board CN1301 (33P, 0.3mm)
VC-370 board CN1501 (80P, 0.4mm)
ST-108 board CN500 (23P, 0.3mm)
ST-108 board CN501 (33P, 0.3mm)
As the timing generator (IC7303) is provided on the CD-537
board, connect the CD-537 board to the following connector
of VC-370 board.
VC-370 board CN1501 (80P, 0.4mm)
5)
The EVF block (SE-151 board) and FP-995 flexible (A/V jack,
LANC jack) must be assembled for connecting the adjusting
remote commander. To remove the EVF block, disconnect the
following connectors.
VC-370 board CN1004 (60P, 0.4mm)
SE-151 board CN2500 (12P, 0.5mm)
6)
By setting the “Forced VTR Power ON mode”, the VTR section
can be operate even if the control key block (PS7450) has been
removed. When removing it, disconnect the following
connector.
VC-370 board CN1008 (14P, 0.5mm)
7)
The MS-234 board need not be connected. But removing the
MS-234 board (removing the VC-370 board CN1020) means
removing the lithium 3V power supply (MS-234 board, BT800),
data such as date, time, user-set menus will be lost. After
completing adjustments, reset these data.
But, the self-diagnosis data and the data on history of use (total
drum rotation time etc.) will be kept even if the MS-234 board
has been removed. (Refer to “6-4.Service Mode” for the data
on the history use and the self-diagnosis data.)
To remove the MS-234 board, disconnect the following
connector.
VC-370 board CN1020 (33P, 0.3mm)
8)
The FP-996 flexible (Remote commander receiver, NIGHT
SHOT LED) need not be connected. To remove it, disconnect
the following connector.
VC-370 board CN1001 (12P, 0.5mm)
9)
The control key block (FK7450) need not be connected. To
remove it, disconnect the following connector.
VC-370 board CN1003 (26P, 0.5mm)
Note2:
Setting the “Forced VTR Power ON” mode (PLAY/EDIT mode)
1) Select page: 0, address: 01, and set data: 01.
2) Select page: A, address: 10, set data: 02, and press the PAUSE
button of the adjusting remote commander.
The above procedure will enable the VTR power to be turned on
with the control key block (PS7450) removed.
After completing adjustments, be sure to exit the “Forced Power
ON mode”.
Note3:
Setting the “Forced Camera Power ON” mode (CAMERA-TAPE
mode)
1) Select page: 0, address: 01, and set data: 01.
2) Select page: A, address: 10, set data: 01, and press the PAUSE
button of the adjusting remote commander.
The above procedure will enable the camera power to be turned
on with the control key block (PS7450) removed.
After completing adjustments, be sure to exit the “Forced Power
ON mode”.
Note4:
Setting the “Forced Memory Power ON” mode (CAMERA-
MEMORY mode)
1) Select page: 0, address: 01, and set data: 01.
2) Select page: A, address: 10, set data: 05, and press the PAUSE
button of the adjusting remote commander.
The above procedure will enable the memory power to be turned
on with the control key block (PS7450) removed.
After completing adjustments, be sure to exit the “Forced Power
ON mode”.
Note5:
Exiting the “Forced Power ON” mode
1) Select page: 0, address: 01, and set data: 01.
2) Select page: A, address: 10, set data: 00, and press the PAUSE
button of the adjusting remote commander.
3) Select page: 0, address: 01, and set data: 0
Summary of Contents for DCR-PC350 - Digital Handycam Camcorder
