CDX-G1200U/G1201U/G1202U/G1280UM
11
Cautions
• Run all ground (earth) leads to a
common ground (earth) point.
• Do not get the leads trapped under a
screw, or caught in moving parts (e.g., seat
railing).
• Before making connections, turn the car
ignition off to avoid short circuits.
• Connect the
yellow
and
red
power supply
leads only after all other leads have been
connected.
For Argentine models: Connect the power
supply lead
ʙ
to the unit and speakers
before connecting it to the auxiliary power
connector.
• Be sure to insulate any loose unconnected
leads with electrical tape for safety.
• Choose the installation location carefully so
that the unit will not interfere with normal
driving operations.
• Avoid installing the unit in areas subject to
dust, dirt, excessive vibration, or high
temperature, such as in direct sunlight or
near heater ducts.
• Use only the supplied mounting hardware
for a safe and secure installation.
Note on the power supply lead (yellow)
When connecting this unit in combination with
other stereo components, the amperage rating of
the car circuit to which the unit is connected must
be higher than the sum of each component’s fuse
amperage rating.
Mounting angle adjustment
Adjust the mounting angle to less than 45°.
Connection/Installation
Precautions
́
To the car’s speaker connector
͂
To the car’s power connector
1
Rear speaker
(right)
È
Purple
2
¾
Purple/black
striped
3
Front speaker
(right)
È
Gray
4
¾
Gray/black
striped
5
Front speaker
(left)
È
White
6
¾
White/black
striped
7
Rear speaker
(left)
È
Green
8
¾
Green/black
striped
12
continuous power
supply
Yellow
13
power antenna (aerial)
/power amplifier
control (REM OUT)
Blue/white
striped
15
switched power
supply
Red
16 ground (earth)
Black
ɡ
To the power antenna (aerial) control
lead or the power supply lead of the
antenna (aerial) booster
It is not necessary to connect this lead if
there is no power antenna (aerial) or
antenna (aerial) booster, or with a
manually-operated telescopic antenna
(aerial).
To AMP REMOTE IN of an optional
power amplifier
This connection is only for amplifiers and
a power antenna (aerial). Connecting any
other system may damage the unit.
Connection
ͬ
from a wired remote control
(not supplied)*
4
White
White/black striped
Gray
Black
Yellow
Red
Blue/white striped
For Argentine models
Front speaker*
1
*
2
Rear speaker*
1
*
2
Gray/black striped
Green
Green/black striped
Purple
Purple/black striped
*
3
*
3
Subwoofer*
1
For details, see “Making
connections” (page 22).
from a car antenna (aerial)
*5
ͭ
*
2
See “Power connection diagram (Argentine
models only)” (page 23) for details.
Power amplifier*
1
ͬ
.
for details
.
(E, EA, AR, KR, IND, AUS)
For Argentine models:
If you have a power antenna (aerial) without
a relay box, connecting this unit with the
supplied power supply lead
ͬ
may damage
the antenna (aerial).
*1 Not supplied
*2 Speaker impedance: 4 Ω – 8 Ω × 4
*3 RCA pin cord (not supplied)
*4 Depending on the type of car, use an adaptor for
a wired remote control (not supplied). For details
on using the wired remote control, see “Using
the wired remote control” (page 23).
*5 Note for the antenna (aerial) connecting
(Argentine models only):
If your car antenna (aerial) is an ISO
(International Organization for Standardization)
type, use the supplied adaptor
ʚ
to connect it.
ɞ
To a common ground (earth) point
First connect the black ground (earth)
lead, then connect the yellow and red
power supply leads.
ɟ
To the +12 V power terminal which is
energized at all times
Be sure to first connect the black ground
(earth) lead to a common ground (earth)
point.
ɠ
To the +12 V power terminal which is
energized when the ignition switch is
set to the accessory position
If there is no accessory position, connect
to the +12 V power (battery) terminal
which is energized at all times.
Be sure to first connect the black ground
(earth) lead to a common ground (earth)
point.
Making connections
.
