Ov
er
v
ie
w
Location and Function of Parts
27
Normally set to “0”. With this setting, addresses are
assigned to the cameras automatically in the
connected order by pressing the POWER button
while holding down the RESET button on the
RM-BR300 Remote Control Unit (not supplied).
You can assign the camera address “1” to “7’
manually by setting these selectors as follows:
Note
Cameras with addresses assigned by setting the
switches to “0” and cameras with addresses
assigned to “1” to “7” cannot be used together. In
addition, the same address cannot be assigned to
multiple cameras manually.
Switch 6 (59.94/50 signal format selector)
Set to ON for output of 50 signal format, or OFF for
output of 59.94 signal format.
The 1080i and 720p formats are automatically
applied to this unit based on the BOTTOM switch
setting of the camera.
Be sure to configure the same setting on this unit
and the camera.
Switches 7 to 10:
Not used. Set them to OFF.
Note
Set the switches before you turn on the power of the
unit.
R
DC 12 V connector
Connect to the supplied AC adapter.
S
Card slot
Install BRBK-SA1 or BRBK-HSD2 optional
interface cards here.
The slot cover is attached to the unit at the factory.
BRBK-SF1 HD Optical Multiplex
Card (not supplied)
A
AUDIO IN L/R jacks (phono type)
Input an audio signal (stereo), which is output from
the AUDIO OUT jacks on the BRU-SF10 HD
Optical Multiplex Unit via the Optical Fiber Cable.
Note
The audio input on this board accepts audio line
signals only. When you input audio signals from a
microphone, etc., it should be connected with a
microphone amplifier so that audio signals with an
appropriate audio level can be input.
B
Optical connector
Performs the optical digital multiplex transmission
of video, audio, external sync and control signals.
A dustproof cap is attached at the factory.
BRBK-HSD2 HD/SD-SDI Output
Card (not supplied)
A
SDI MONITOR OUT connector (BNC type)
Outputs down-converted SD-SDI signals
(conforming to SMPTE259M serial digital
interface standards during 1080/59.94i or 720/
59.94p, and ITU-R BT.656 serial digital interface
standards during 1080/50i or 720/50p) and HD-SDI
signals (conforming to SMPTE292M serial digital
interface standards).
When the menu display for the camera is turned
ON, the menu display signal that overlaps the
images is output from this connector. When the SD-
SDI output card is installed in the card slot of the
BRU-SF10 HD Optical Multiplex Unit, you can
also hide the menu display by using the DATA MIX
switch on the BRU-SF10. For details, see “Images
when menu display is ON” on page 28.
B
SDI connectors 1, 2 (BNC type)
Outputs down-converted SD-SDI signals
(conforming to SMPTE259M serial digital
interface standards during 1080/59.94i or 720/
59.94p, and ITU-R BT.656 serial digital interface
standards during 1080/50i or 720/50p) and HD-SDI
signals (conforming to SMPTE292M serial digital
interface standards).
When the menu display for the camera is turned
ON, you can select whether to overlap the menu
display with the image by using the
C
panel
Camera
address
0
1
2
3
4
5
6
7
Switch 3
OFF ON
OFF ON
OFF ON
OFF ON
Switch 4
OFF OFF ON
ON
OFF OFF ON
ON
Switch 5
OFF OFF OFF OFF ON
ON
ON
ON
AUDIO IN
BRU
BRBK-SF1
L
R
2
1
SDI OUT
MONITOR
1
2
BRBK-HSD2
ON
HD
SD
OFF
1
3
2