manualshive.com logo in svg

Sony Ericsson Developer's Board, Manual, Page: 14 / 28

Share
Download
Sony Ericsson Developer's Board Manual Download Page 14

Developer's Board Manual Rev A

Page 14 of 28

SEM/CX-02:0061/MAN

3 Functional 

Description

3.1 General

The developer's board was designed to give you a platform to familiarize yourself with the operation of the various
module families and allow you to start developing your application.

The developer's board provides an RS-232 interfaces, appropriate voltage levels, audio interface, IO control and a
mechanical mounting platform.

The current revision of the developer's board is P1F.   The discussion in this manual is written around this revision
of the board.  Assembly drawings of several revisions are included for completeness.  The reference designators
are consistent across the revision to facilitate using this manual for common features.

The revision of the developer's board is imprinted on the backside of the PCB.  Turn over the board and locate the
TVK 117 2403 number.  The revision is the alphanumeric at the end of this number

Summary of Contents for Developer's Board





























Reviews:

No comments