manualshive.com logo in svg

Sony Ericsson Developer's Board, Manual, Page: 10 / 28

Share
Download
Sony Ericsson Developer's Board Manual Download Page 10

Developer's Board Manual Rev A

Page 10 of 28

SEM/CX-02:0061/MAN

2.4  Connecting the Hardware

Once you have successfully mounted the module on the developer's board and confirmed the system
requirements you may setup the developer's board.  The following drawings indicate how to do this.

2.4.1  DM-xx Family Connection

Figure 4: DM-xx Connection Diagram

•

  Connect serial cable from Suzy board port 1 to an available serial port on the PC.

•

  The DC power supply provides the necessary 12VDC.

•

  Connect the power cable to the power supply and the AC outlet.  The included cable is for North America.

Elsewhere, you may simply substitute the appropriate line cord.

•

  Connect the output of the power supply to the power jack on the Suzy board.

•

  Attach the provided antenna cable to the SMA antenna jack on the Suzy board or directly to the primary RF

output port of the module.

•

  For voice calls plug-in the provided Hands-free Speaker/Microphone.

Summary of Contents for Developer's Board





























Reviews:

No comments