sonaca aircraft S201 Aircraft Flight Manual Download

Page: 151 / 283

S201 AFM

5 - PERFORMANCE

5.3 - PERFORMANCE TABLES

AND DIAGRAMS

27/06/2019

SONAIR-S2-D-MAN-006

Page : 5-9

Rev. : A

Following altitude loss can be expected during a wing level stall:

Power setting

Altitude loss

Idle

250 ft

75 %

450 ft

These values are valid for all flaps settings and for any weight & balance
configuration within the approved limits.

5.3.5

WIND COMPONENTS

The maximum demonstrated cross wind component for take-off and landing is:

19 kts

CAUTION

Always maintain the aircraft in straight flight (no slip) using gentle rudder

and ailerons control inputs during stall. Failing to do so will result in spin.

The aircraft nose is off-centered by 3° from the aircraft centerline. Use Turn

and Slip indicator to maintain straight flight during stall.

Summary of Contents for S201




























































































































































































































































































Search results

Summary of Contents for S201

Reviews:

Related manuals for S201

Brands by name

Popular brands

sonaca aircraft S201, Aircraft Flight Manual

Search results

Summary of Contents for S201

Reviews:

Related manuals for S201

Brands by name

Popular brands