background image

**ON A/C 10003, 10040, 10043, 10046, 10048, 10052, 10063, 10076, 10080, 10083, 10085

10086, 10089,

 

10091, 10093, 10096, 10098, 10100, 10103, 10118, 10120, 10127, 10132

10139, 10141, 10143

10146,

 

10148

10151, 10153, 10155

10339, 15026

15316

, 15317−15999

and ON A/C 10004

10039, 10041

10042, 10044

10045, 10047, 10049

10051, 10053

10062,

10064

10075, 10077

10079, 10081

10082, 10084, 10087

10088, 10090, 10092, 10094

10095, 10097,

 

10099, 10101

10102, 10104

10117, 10119, 10121

10126, 10128

10131, 10140, 10142, 10147, 10152,

 

10154, 15001

15025 Post SB670BA

34

009

TASK

 

34

54

00

720

802

−PSA

Functional Test of the ATC Altitude Reporting (Mode C)

1.

General

A.

The maintenance procedure that follows is for the functional test of the altitude reporting (Mode
C). The transponder 1 is installed on the left side of the main avionics compartment . The
transponder 2 is installed on the right side of the main avionics compartment. This procedure is
applicable to the transponder 1 and transponder 2.

2.

Job Set

Up Information

A.

Tools and Equipment

REFERENCE

DESIGNATION

ATC

601 (FUTURE

PROCUREMENT P/N IFR 6000)

Test Set 

 Transponder Mode S

IFR 6000

Ramp Test Set (Transponder, TCAS, DME)

ADTS405F

Test Set 

 Air Data

ADCRJ

612

Connector Kit 

 Pitot Static Pressure Test

B.

Reference Information

MANUAL NO

REFERENCE

DESIGNATION

CSP

B

001

TASK 12

00

00

867

801

Standard Aircraft Configuration for Maintenance

CSP

B

001

TASK 24

00

00

861

801

Connect Electrical Power to the Aircraft

CSP

B

001

TASK 24

00

00

861

802

Remove Electrical Power from the Aircraft

CSP

B

001

TASK 24

00

00

910

801

Electrical/Electronic Safety Precautions

CSP

B

001

TASK 32

61

00

867

801

Put the Aircraft in a Weight

Off

Wheels Configuration

with the Aircraft on Ground

CSP

B

001

TASK 32

61

00

867

802

Remove the Aircraft From the Weight

Off

Wheels

Configuration with the Aircraft on Ground

Internal PSA Document

CRJ-900

AIRCRAFT MAINTENANCE MANUAL

PSA AIRLINES, INC REVISION

EFFECTIVITY: Ref page 1 of Blue Page

 

 

34-54-00-720-802-PSA Rev A

AMM - Insert after Task 34-54-00-720-802-A01 of AMM 34-54-00

Remove Rev 34-54-00-720-802PSA dated Sep 17/14 and insert 34-54-00-720-802-PSA Rev A dated 10/12/15

10/12/15

Page 1 of 13

Summary of Contents for CRJ-900














Reviews: