digital recorder
HD T2
SAFETY INFORMATION:
To reduce the risk of fire or electric shock, do not expose the unit to rain or moisture.
ATTENTION
: To avoid the risk of fire and electric shock, do not remove the cover of
the unit (or back cover). In the event of a fault, consult a qualified technician.
DANGER: TO REDUCE THE RISK OF FIRE AND ELECTRIC SHOCK, DO NOT
EXPOSE THE UNIT TO RAIN OR HUMIDITY.
ATTENTION: TO PREVENT ELECTRICAL SHOCK, INSERT THE WIDE CONTACT
OF THE PLUG TO THE WIDE OPENING, AND PLUG IT IN COMPLETELY.
Do not expose the appliance to dripping or splashing liquid, and do not place objects
filled with liquid on it, such as a vase.
IMPORTANT WARNINGS
In addition to the careful attention payed on quality standards, safety was also an
important factor in the design process of every set-top boxes. However, security is
your responsibility, too. The following list contains important information to help you to
use the set-top box and its accessories on the correct way.
INSTALLATION
1. Reading and following the warnings – Before using the appliance, read all of the
safety warnings. Keep these warnings in every case.
2. Retaining the warnings – Retain the safety warnings, later you might need them.
3. Acting according to the warnings– Keep the safety warnings.
4. Polarization – Some appliances are distributed together with polarized AC power
cords. These power cords can be used with corresponding type connectors. If
necessary, have electrical outlets replaced by an electrician. The power cord
should only be used with a power outlet, extension cord, distributor in which the
forks of the power cord can fully be inserted in without being left loose.
5. Power sources – The device should only be operated from a power source
conforming to the information label on the rear panel. If you are not sure of the
electrical parameters of your home, consult a specialist.
6. Overloading – Be careful not to overload the used wall sockets or extension
cords as this may result in fire or electric shock. Overloaded connectors, cracked
insulated cables, broken terminals are potential sources of hazard, can cause
fire or electric shock. Regularly inspect your wiring and consult a technician if
necessary.
7. Power cord protection– Prevent the power cord from being stepped on or getting
broken, especially at the connecting parts of the appliance and the branchings of
the power plugs. Make sure that the electrical connector is easily accessible and
if needed, immediately accessible for such devices, which do not have a separate
power switch.
8. Ventilation – The vents on the appliance housing are designed to ensure proper
ventilation of the unit and to prevent it from overheating. Please, never cover these
openings with any objects placed on or near the device. Only place the appliance
in a well-ventilated area and do not place it between different kinds of shelves or
inside cabinets, unless proper ventilation of the appliance and heat dissipation
during operation are ensured.
9. Accessories – Use only accessories approved by the manufacturer.
10. Water and humidity – Do not use the appliance near humidity, such as bathtubs,
washbasins, kitchen sinks: do not place the appliance into damp rooms, e.g. a
swimming pool or a similar place. Please, pay attention to safety. For an appliance
or accessory supplied with a a power cord, use only devices that have been
marked with the appropriate safety certificates. Modifications to these devices are
prohibited if the endanger safe operation. If you need advice, consult a qualified
technician if necessary.
11. Accessories – Do not place the appliance on an unstable trolley, stand, tripod, shelf
or table. The product may fall and cause serious injury. Use only the accessories
approved by the manufacturer for storing the appliance. When installing the
mounting the device, always follow the manufacturer’s instruction and always
use accessories approved by the manufacturer or the accessory manufacturer.
Contact the distributor if you need advice.
11a. Take extra care when using the appliance placed on a roller stand. Avoid
sudden stops, uneven surfaces, and other obstructions that could cause the
tip-over of the bracket, personal injury or malfunction of the equipment.
12. Grounding outdoor antenna – In case of using an outdoor antenna, make sure
that the antenna is properly grounded to provide protection from static electricity
that may accumulate.
13. Electric wires – Installing an outdoor antenna system is not recommended nearby
electric wires, other electric lighting or electrical network, and at places where
the antenna might get into contact with or fall on such wires. Outdoor access or
touching is strictly prohibited and is life-threatening. Installing an outdoor antenna
is a dangerous operation and we recommend you to have it installed by a qualified
technician.
Use
14. Cleaning – Unplug the appliance from the electrical outlet before cleaning. Do
not use chemicals, only a slightly dampened soft cloth to clean the cover of the
appliance.
15. To prevent the risk of fire or electric shock, do not expose this appliance to water
or other moisture.
16. Lightning – Unplug the power cable from the outlet by the time of storm or lightning,
and if you are not planning to use the appliance for an extended period of time,
remove also antenna cable from it. This will prevent the unit from getting damaged
by a lighting strike.
Repair
17. Repair – Never attempt to repair the appliance at home. Removing the cover will
expose you to the risk of a serious, life-threatening electric shock and will invalidate
any warranty applicable to the device. Any repairs should only be carried out by
qualified service personnel.
18. State requires service – Unplug your appliance from the power supply and contact
a qualified service provider under the following conditions:
a. If the power cable of the appliance is damaged
b. If the appliance is exposed to moisture or objects are trapped inside it
c. If liquid has leaked into the appliance
d. If the unit does not operate as described in the operating instructions. Only
make settings on this machine that are described in this manual. Other settings
may not work properly and it may take a long time for the appliance to function
properly.
e. If the unit has been dropped and the cover has been damaged
f. If there is a significant change in the device performance. If any of the above
listed points applies, contact a qualified service center
19. Replacement parts – Only replacement parts that are approved by the
manufacturer or an authorized service center may be used for service purposes.
Using of replacement parts from other sources may cause malfunction or personal
injury to the unit and void the warranty applicable to this unit.
20. Heat sources – Do not expose the appliance to radiating heat. Do not store the
appliance nearby devices that emit significant heat (such as radiators, amplifiers, etc.)
21. Mounting on wall or ceiling – The device may only be mounted on wall surfaces
or accessories as recommended by the manufacturer or distributor, applying any
other mounting manners may cause personal injury or the malfunction of the
appliance.
22. The design, functions and accessories of this device may differ from what is
described in this manual without prior notice. If there is a difference, always the
concrete product can be considered as the final version.
23. The Hungarian DVB-T broadcasts are optimized for roof antenna, good quality
television reception is provided only in case of properly set, suitable broadband
roof antenna and good quality cabling. In case of reception problems, consult an
antenna technician or consult your broadcaster.
24. The list of formats that can be played with the device’s media player function is
only informative. Files with particular codec and compression settings may not be
playable even if they are in supported file format by your device. The list of supported
file types is subject to change without prior notice during firmware upgrade.
INITIAL STEPS
First installation:
After the unit is switched on for the first time, the unit displays the Init Install menu.
You can select between the OSD Language, Country, LCN options with the navigation
buttons.
Select the appropriate menu with the navigation buttons, and select from the options.
Accept the selected option by pressing the remote control’s „OK” button. In case of
the LCN option is switched on, the device sorts the channels according to the channel
assignment defined by the service provider. Select the „Next” menu to start station search.
Installation:
1. Press the „MENU” button on the remote control.
2. Use the „RIGHT” / „LEFT” button to select the „Installation” menu in the lower
pictogram menu bar.
3. Use the „UP” / „DOWN” buttons to select the desired item, then hold pressed the
„OK” button.
4. Press the „EXIT” button on the remote control to exit.
Automatic search:
To select Auto search, press the „DOWN” then the „OK” button.
Manual channel search:
1. Use the navigation buttons to select the Manual Search menu then press the „OK”
button.
2. Use the navigation buttons to set Channel No., the Frequency and the Bandwidth.
3. After selecting the Start search option, press the „OK” button to start searching.
6
