2
3
Programming
Initial installation: Record the first control
3.1
Add a new control when RTS 25 DC is not accessible
3.2
Set the RTS 25 DC in its pro-
gramming mode by pressing the
PROG button until the blind moves
briefly (UP/DOWN).
The RTS 25 DC will remain ready to
record the RTS control for two min-
utes.
Remove a control
3.3
To remove a RTS control, set the RTS 25 DC in its programming mode (see § 3.1), then press briefly the programming button of
the RTS control you wish to remove.
It is also possible to “wake up” the RTS 25 DC with another RTS control which is also recorded (see § 3.2),
then press shortly the programming. button of the RTS control you wish to remove.
To remove all the controls, refer to chapter 6 (complete reset of the RTS 25 DC).
SEVERAL CONTROLS IN ONE RTS 25 DC
You can record up to 12 RTS controls
into the RTS 25 DC following the
same procedure described above.
ONE CONTROL FOR SEVERAL RTS 25 DC
press the PROG. Button of all RTS 25
DC you wish to control and press
briefly the programming button of the
RTS control.
blinds move briefly (UP/DOWN)
indicating that the control has been
memorised by the RTS 25 DC which
automatically quit their programming
mode.
Press briefly the programming button on
the RTS control you wish to record.
The blind moves briefly
(UP/DOWN) indicating that the control
has been memorised by the RTS 25
DC which will then automatically quits
its programming mode.
Press the programming button of a
previous programmed RTS control
for more than 2 seconds.
The blind moves briefly (UP/DOWN)
indicating that the RTS 25 DC has
entered in its programming mode.
Move the blind to its UP limit
with the
▲
button of the RTS
control and immediately
press the
■
button briefly.
Press the
■
and
▼
buttons
simultaneously until the
blind begins to move
DOWN.
Stop the blind at the inter-
mediate position you wish.
If necessary, adjust this
position with the
▼
or
▲
buttons.
Press the
■
button for
more than 5 sec.
The blind moves briefly
(UP/DOWN), IP1 is now
recorded.
Move the blind at its
DOWN limit with the
▼
button of the RTS control
and immediately
press the
■
button briefly.
Press the
■
and
▲
buttons
simultaneously until the
blind begins to move UP.
Stop the blind at the
intermediate position you
wish.
If necessary, adjust this
position with the
▼
or
▲
buttons.
Press the
■
button for
more than 5 sec.
The blind moves briefly
(UP/DOWN), IP2 is now
recorded.
3V
LITHIUM
RENATA
CR 2430
SW
IS
S
M A D
E
3V
LITHIUM
RENATA
CR 2430
Press briefly the programming
button on the new RTS control
you wish to add.
The blind moves briefly (UP/DOWN)
indicating that the new control has
been memorised by RTS 25 DC.
> 2 sec.
3
Intermediate positions
4.2
Programming the 1st intermediate position
(IP1)
- from the
UP
limit
a
Programming the 2nd intermediate position
(IP2)
- from the
DOWN
limit
b
When the blind is at its UP limit:
Press briefly on the
■
button.
The blind will move and stop at the 1st intermediate position (IP1).
When the blind is at its DOWN limit:
Press briefly on the
■
button.
The blind will move and stop at the 2nd intermediate position (IP2).
Using the intermediate positions
c
If you record a new IP, this will automatically erase the previous one.
If you want to erase without recording a new one, press briefly on the
■
button to reach the IP you want to erase. Then:
to erase IP1, press the
▼
and
■
buttons simultaneously for more than 5 seconds.
to erase IP2, press the
▲
and
■
buttons simultaneously for more than 5 seconds.
To erase both, just press the
■
button for more than 5 seconds.
The blind moves briefly (UP/DOWN) indicating that the concerned intermediate position has been erased.
Delete an intermediate position
d
With the RTS 25 DC, it is possible to set one or two intermediate positions: one accessible at the top, when the blind is fully
retracted
(IP1)
and one from the bottom
(IP2)
. To record these positions, the RTS 25 DC has to record the time for the blind
to go from one end limit to the desired IP.
4
TILTING speed adjustment
5.2
The speed of the motor can be reduced in order to make the adjustment of the slats easier during the tilting operation.
> 5 sec.
after
3 seconds
STOP
IP1
UP
> 5 sec.
STOP
IP2
M o v e t h e b l i n d
approximately
I
down
of the window.
Press the
▼ ▲
and
■
buttons simultaneously
for 2 seconds.
The blind starts to move
UP and DOWN alternatively.
Press several time the
▲
button to increase or
▼
button to decrease the
speed.
Press the
■
button for
more than 5 seconds when
the speed is convenient.
The blind moves briefly
(UP/DOWN) to indicate
that the low speed is set.
Move the blind approx-
imately
I
down of the
window.
Press the
▲
and
■
buttons
simultaneously until the
blind begins to move UP
and STOP it immediately to
prevent reaching its end
limits.
Adjust the tilt angle with
the
▼
or
▲
buttons (the
blind operates at low
speed).
Press the
■
button for
more than 5 sec.
The blind moves briefly
(UP/DOWN), the tilt angle
is recorded.
> 5 sec.
> 5 sec.
(for lift operating, please refer to section 4)
5
Operating of lift/tilt applications
UP/DOWN/STOP/TILT commands
5.1
or
+
-
Automatic slat tilting / Intermediate position
5.3
With the RTS 25 DC, it is possible to program an automatic tilting of the slats and an intermediate position (IP).
You can choose to program either the slat tilting or the IP or both.
a
Programming of the slat tilting
(Set tilting speed before programming the automatic tilting § 5.2)
STOP
adjust
the angle
4
Operating of lift only applications
UP/DOWN/STOP commands
4.1
1
To lower or raise the blind, press briefly the
▼
and
▲
buttons of a RTS control.
2
To stop the blind, press briefly the
■
button of a RTS control.
(for lift/tilt operating, please refer to section 5)
All rights reserved to make changes due to technical improvements
All rights reserved to make changes due to technical improvements
All rights reserved to make changes due to technical improvements
1
2
1
2
1
2
3
4
1
2
3
4
1
2
3
4
1
2
3
4
RECORDED
RECORDED
or
after
3 seconds
DOWN
3/4 Down
3/4 Down
To lower or raise the blind, press the
▼
or
▲
buttons of an RTS control briefly for 1 sec.
To stop the blind, press the
■
button of an RTS control (1 sec.).
To tilt the slats, press and hold the
▼
or
▲
buttons of an RTS control.
If you hold the control buttons for more than 6 seconds,
the blind will start to move continuously up to its end limits.
STOP/IP
DOWN
UP
STOP/IP
DOWN
UP
Note: this position has to be more than 6 seconds running time from the down limit.
