background image

                        

 

6. COMMUNICATION 

INTERFACE: 

 

The UPS provides both computer interfaces, smart software (RS-232) and dry 

contact (DB-9); by using different software and cable, the UPS shows different 

monitoring function. 

6.1 

The definition and setup for RS-232 is as following: 

 

Baud Rate  : 2400 dps 

 

Data Length  : 8 bits 

 

Stop Bit 

: 1 bit 

 Parity  : 

None 

 

 

 

Pin #6 

: RS-232 data Tx out. 

 

Pin #7 

: Common of Pin #6 and Pin #9 

 

Pin #9 

: RS-232 data Rx In 

 

6.2 

The definition and setup for DB9 (optional) is as following: 

 

Pin #2 

: AC Power Failure 

 

Pin #4 

: Common GND of Pin #2 & Pin #5 

 

Pin #5 

: UPS Battery Low 

 

Pin #6 

: Turn off UPS 

 

Pin #7 

: GND of Pin6 

 

The interface with computer is diagramed as above for your reference.    Use Pin #4 as the 

common of Pin #2 and Pin #5, Pin #2 and Pin #4 will become close loop from open when 

the utility fails, Pin #5 and Pin #4 will become close loop from open when the battery level 

is low. 

The UPS will shut down itself when the high level signal from RS-232, sustained for 

3 seconds, is applied between Pin #6 and Pin #7. 

 

  5   4   3   2   1  

    9 8 7 6 

Summary of Contents for SS-1000L














Reviews: