manualshive.com logo in svg

Solowave Big Backyard F23230, Assembly Instructions Manual, Page: 4 / 28

Share
Download
Solowave Big Backyard F23230 Assembly Instructions Manual Download Page 4

 (2) Ground Side (1 x 5 x 56")

 

3660731

(1) Floor Front (2 x 3 x 58-1/4") 

3660702

(2) Roof Side (1 x 4 x 47-3/4") 

3660719

(2) Ground Diagonal (2 x 3 x 35") 

3660304

(1) Ground Front (1 x 5 x 59-1/4") 

3660730

(1) Front Top (1 x 4 x 58-1/4") 

3660721

(2) Centre Divider (1 x 4 x 35-3/4")  

3660707

3610710

(1) Rope Bottom (1 x 6 x 59-1/4")  

3660711

(1) Floor Back (5/4 x 4 x 59-1/4") 

3660704

 (1) Back Top (1 x 4 x 59-1/4") 

3660703

(2) Cedar Gap Board (1 x 5 x 35-1/4")  

 (1) Side Joist (2 x 2 x 55") 

3660705

(1) Floor Joist (5/4 x 4 x 58-1/2") 

3660712

(2) CE Wall Board(Unstained) (1 x 6 x 23-1/2") 

(4) CE Wall Board(Stained) (1 x 6 x 23-1/2")

 

(1) Lower Chalk Wall (1 x 4 x 31") 

3660717

3610702

3620702

(1) Panel Frame (1 x 2 x 25-1/2") 

3660726

(2) Rock Rail (5/4 x 4 x 51") 

3660714

(2) Rock Side (2 x 2 x 49-1/2") 

3660715

(1) SW Roof Mount  (2 x 4 x 59-1/4")

 

3660752

(5) CE Rock Board(1 x 6 x 23-1/2") 

3610703

(Unstained) 

3610621

(2) Floor End(1 x 6 x 38-1/4") 

3660743

(4) CE Gap Board (1 x 4 x 38-3/4")

                       

3620839

  

(10) Cedar Floor Board  (1 x 5 x 35-1/4")

(1) Roof Mount (2 x 3 x 23")

 

3660729

Nominal 

Size

Actual 

Size

 2" x 6"

 1 3/8" x 5 3/8"

 2" x 4"

1 3/8" x 3 3/8"

2" x 3"

1 3/8" x 2 3/8"

2" x 2"

1 1/2" x 1 1/2"

 5/4" x 4"

1" x 3 1/2"

 1" x 5"

5/8" x 4 1/2"

 1" x 6"

5/8" x 5 3/8"

Wood Identification

 

(Reduced Size Parts)

Before you assemble your fort, please identify and count your boards.
Remember, wood is a product of nature and affected by changes in 

weather.  Although the wood in this set has been carefully selected, expansion 

and contraction may cause slight warping, twisting or 

checking of the boards while in the carton.  This is a natural 

characteristic of wood and 

will not

 affect the structural integrity of 

your set.
Profile dimensions denoted in these instructions are based on wood size before 

machining and finishing.  Actual size will be smaller.  

4

Summary of Contents for Big Backyard F23230





























Reviews:

No comments