Solowave Big Backyard F23230 Assembly Instructions Manual Download Page 15 | Manualshive

Page: 15 / 28

Solowave Big Backyard F23230 Assembly Instructions Manual Download Page 15

Roughly 20"

#12 x 2"

Pan Screw

(Pre-drill pilot holes)

Mount screws from edge

NOTE: Start at top and

attach top board ¼"

below mounting holes.

1 x 6 x 23½"

CE Rock Boards

1 x 6 x 23½"

CE Wall Boards

(Unstained)

#8 x 1½"

Wood Screw

3/4"

5/4 x 4 x 51"

Rock Rails

Tops mount

to Fort

2 x 2 x 49-1/2"

Rock Sides

6A

R.Side View

6B

Front View

HARDWARE LIST

6 pcs #12x2" Pan Screw

28 pcs #8x1-1/2" Wood Screw

WOOD PARTS LIST

2 pcs 5/4x4x51" Rock Rail

2 pcs 2x2x49-1/2" Rock Side

5 pcs 1x6x23-1/2" CE Rock Board

2 pcs 1x6x23-1/2" CE Wall Board

(

unstained)

the (2) Rock Rails.

*Pre-drill pilot holes, with a 1/8" drill bit and evenly space the

drilled holes as shown in the Side View.

Using (3)Pan Screws per Rock Rail, attach(2) Rock Sides to

*Evenly space the Rock Boards in between both CE Wall Boards.

Using (4) Wood Screws per board, attach (5) CE Rock Boards &(2) CE Wall Boards

to the Rock Rails.

Alternate Rock Boards as desired. Holes in middle of board

MUST be oriented to the top of the Climbing Wall for proper mounting of Rocks.

15

«
...
13
14
15
16
17
...
»

Summary of Contents for Big Backyard F23230





























Reviews:

No comments