manualshive.com logo in svg

Solowave Big Backyard F23230, Assembly Instructions Manual, Page: 26 / 28

Share
Download
Solowave Big Backyard F23230 Assembly Instructions Manual Download Page 26

Diagonal using (2) 

SW Posts, Post, Ground

screws each.

Ground Stakes into

 firm soil and attach to 

Drive 2 x 2 x 14" 

Drive one Stake 

and attach to 

back of Rock Wall.

WOOD PARTS LIST

5 pcs 2x2x14" Ground Stakes

HARDWARE LIST

10 pcs #8x2-1/2" Wood Screw

Drill Pilot

Holes. Use

Stake as 

guide.

#8 x 2-1/2" 

Wood Screw

Ground level

(Drive stake10½" 

into ground)

Stakes Installation

•Use a scrap wood piece in between the top of the Ground Stake &  

the Sledge Hammer to protect the stake from damage.

•Stakes are to be secure to the posts and the ground.

•Firmly anchor unit to ground before use.

•Check for looseness, re-secure and replace if necessary.

•

DO NOT USE CONCRETE OR OTHER MATERIALS FOR ANCHORING STAKES!

•Drive Ground Stakes into the ground, making sure that the ground is 

firm underneath the stakes.

•Using (2) Wood Screws, attach each stake to the corresponding

 post as shown below.

Sample Ground Stake Installation

1

3

26

Summary of Contents for Big Backyard F23230





























Reviews:

No comments