manualshive.com logo in svg

Solid State Logic AWS 924, Owner'S Manual

Looking for the Owner's Manual of the versatile Solid State Logic AWS 924? Look no further! Download your free manual directly from our website, manualshive.com, and unravel the full potential of this exceptional product.

Share
Download
background image

C

HANNEL

S

TRIP

Note that throughout this section, where the 924 and 948 differ, the 924 channel strip is shown on the left and the

948 on the right. Text specific to one model is framed in a blue box with the model name at the top.

Overview

Channel meters and peak lights, showing analogue levels or DAW levels depending on console Focus mode.

See Page 3-6.

REC

: DAW channel is in Record Ready;

EDIT

: channel is assigned to the plug-in editor.

See Section 4.

Track bus routing and source selection: Pre-fader (

PRE

), post-pan (

PAN

) or post fader (neither)

See Page 3-10.

Dynamics assignment: Press

1

or

2

(either for Stereo channels) to assign available compressors.

Compressor source is post EQ;

IP

or

OP

move it to begninning or end of chain.

See Page 3-6.

Input section

See Page 3-5.

EQ section

See Page 3-7.

Cue and FX sends. Press pot to activate.

948: hold

ALT/EFX Sel

and press pot to switch between odd/even sends or EFX.

See Page 3-9.

Channel pan and routing buttons for Mix and Rec busses. (948:

RETURN

enables 48-chan mixing)

See Page 3-11.

V-Pot, plus

solo

and

cut

switches. Control either DAW channel or console channel,

depending on the console Focus mode. Press V-pot to operate V-sel switch.

See Page 3-12.

Channel display, showing a variety of DAW and console information.

See Page 3-11.

SEL

switch, selects channel for editing in DAW or centre section, depending on console Focus

mode. Also used as a Record Ready switch and Plug-in Edit selectors.

See Page 3-12.

Channel

solo

and

cut

switches for DAW or console channel, depending on the console Focus mode.

See Page 3-12.

Channel fader. Controls either DAW channel or console channel, depending on the console Focus mode.

See Page 3-12.

AWS 924

AWS 948

Analogue Operations

AWS 924-948 Owner’s Manual

Page 3-5

Summary of Contents for AWS 924



















































































































































































































































Reviews:

No comments

Related manuals for AWS 924

Maestro MR550 Owner'S Manual preview
MR550
Brand: Maestro Pages: 52
Faggiolati Pumps GM Series Instructions For Installation And Use Manual preview
GM Series
Brand: Faggiolati Pumps Pages: 38
Ibanez FL9 Flanger Service Manual preview
FL9 Flanger
Brand: Ibanez Pages: 11
Euro-Pro Bravetti Platinum Pro EP552HL Owner'S Manual preview
Bravetti Platinum Pro EP552HL
Brand: Euro-Pro Pages: 4
Tesla MX505WXB User Manual preview
MX505WXB
Brand: Tesla Pages: 44
Mark MAX 4.2 USB User Manual preview
MAX 4.2 USB
Brand: Mark Pages: 12
IMG STAGELINE MMX-830 Instruction Manual preview
MMX-830
Brand: IMG STAGELINE Pages: 24
IMG STAGE LINE PMX-100 Instruction Manual preview
PMX-100
Brand: IMG STAGE LINE Pages: 18
IMG STAGE LINE MMX-142 Instruction Manual preview
MMX-142
Brand: IMG STAGE LINE Pages: 26
Whirlwind MPM4 Operation Manual preview
MPM4
Brand: Whirlwind Pages: 12
SIRI 13 Instructions For Use Manual preview
13
Brand: SIRI Pages: 20
Dunlop DVP4 VOLUME X Operation Manual preview
DVP4 VOLUME X
Brand: Dunlop Pages: 2
Dunlop CRY BABY WULDE WAH ZW-45 Manual preview
CRY BABY WULDE WAH ZW-45
Brand: Dunlop Pages: 2
Dunlop Cry Baby CBM105Q Setup Instructions preview
Cry Baby CBM105Q
Brand: Dunlop Pages: 2
Dunlop CBM95 Cry Baby Mini Wah Setup Instructions preview
CBM95 Cry Baby Mini Wah
Brand: Dunlop Pages: 2
Dunlop 535Q Owner'S Manual preview
535Q
Brand: Dunlop Pages: 8
Louroe Electronics MLA-6 Installation And Operating Instructions Manual preview
MLA-6
Brand: Louroe Electronics Pages: 8
Caframo Crossover 1540 User Manual preview
Crossover 1540
Brand: Caframo Pages: 48

Brands by name

Popular brands

Load more brands