manualshive.com logo in svg

Solid State Logic AWS 924, Owner'S Manual

Looking for the Owner's Manual of the versatile Solid State Logic AWS 924? Look no further! Download your free manual directly from our website, manualshive.com, and unravel the full potential of this exceptional product.

Share
Download
background image

HUI A

UTOMATION

The AWS’s touch sensitive moving faders can be used to write automation for the DAW fader. Most automation functions

can be enabled from the soft key matrix below the console’s display screen. Within this are menus for Automation Enables,

Automation Modes, Grouping and Editing functions.

A-FADA, which uses DAW automation to control analogue faders, is descibed on Page 4-7.

Note: Automation data can usually only be written when the DAW is in Play, Half-Speed Play or Record.

Automation Enables

Automation Enable modes (

AuEn

) globally engage or disengage automation for the following items: Faders, Pans, Plug-Ins,

Cuts (

Mute

), Sends and Send Muting (

SnMute

). Holding down the

OPTION

button then pressing any of the sub menu

buttons will toggle automation on or off for all controls.
The

Pan

automation enable includes both Channel and Send Pan.

Automation Modes

There are several Automation Modes (

AuMo

) available including: Write, Touch, Latch, Trim, Read and Off.

To change automation mode on a channel select an automation mode from the soft key menu and press the auto button

on a channel fader. Holding down

OPTION

then selecting an automation mode from below the TFT screen will change

automation modes on all channels. Changes within the DAW will be reflected on the console.

Refer to your DAW manual for more information on its specific automation features.

Automation Status Display

Pressing and holding the auto button to the left of a channel fader will display the current

automation mode for that channel in the channel scribble strip display. To display the automation

mode on all channels select the Status Group (StGr) soft menu, and press Auto.
The automation LED indications are as follows:

No LED

Automation off

Green LED

Read automation mode

Red Flashing LED

DAW is ready to write automation in write, touch or latch modes.

Red solid LED

Writing automation data

Red and Green LEDs Trim automation mode

DAW Control

AWS 924-948 Owner’s Manual

Page 4-29

Summary of Contents for AWS 924



















































































































































































































































Reviews:

No comments

Related manuals for AWS 924

ZETRON 4010 Service Manual preview
4010
Brand: ZETRON Pages: 123
Calrec Zeta Operator'S Manual preview
Zeta
Brand: Calrec Pages: 144
Fast & Fluid Management GA450 Manual preview
GA450
Brand: Fast & Fluid Management Pages: 32
Akura APTMIC110AR Instruction Manual preview
APTMIC110AR
Brand: Akura Pages: 10
Kemar KSB-300R Instruction Manual preview
KSB-300R
Brand: Kemar Pages: 62
Ratek BTR10-12V User Manual preview
BTR10-12V
Brand: Ratek Pages: 16
Omcan SM-IT-0053-F Instruction Manual preview
SM-IT-0053-F
Brand: Omcan Pages: 28
Zoom LiveTrak L-20R Operation Manual preview
LiveTrak L-20R
Brand: Zoom Pages: 120
IVIE 802A Operation And Owner'S Manual preview
802A
Brand: IVIE Pages: 8
Fulltone Fat-Boost Quick Start Manual preview
Fat-Boost
Brand: Fulltone Pages: 2
NEC NCS Console 4.0 User Manual preview
NCS Console 4.0
Brand: NEC Pages: 20
NEC NEAX 2000 IVS Command Manual preview
NEAX 2000 IVS
Brand: NEC Pages: 473
NEC NEAX 2000 IVS Installation Manual preview
NEAX 2000 IVS
Brand: NEC Pages: 173
NEC IP4WW60DDSSACON Manual preview
IP4WW60DDSSACON
Brand: NEC Pages: 11
Samson MIXPAD MXP144 Owner'S Manual preview
MIXPAD MXP144
Brand: Samson Pages: 24
Fulltone Supa-Trem2 Manual preview
Supa-Trem2
Brand: Fulltone Pages: 2
Inter-m LM-6414 Operation Manual preview
LM-6414
Brand: Inter-m Pages: 16
Inter-m MX-1646D Operation Manual preview
MX-1646D
Brand: Inter-m Pages: 32

Brands by name

Popular brands

Load more brands