background image

Setting Your Workstation(s) to Communicate via ipMIDI

The AWS software uses 10 virtual MIDI ports which are pre-assigned as follows:

* Note that MIDI port 4

or

ipMiDI port 7 can be used for MTC input, allowing MTC to be connected from systems (such as

RADAR) that do not support the ipMIDI driver. MTC should only be routed to one port at a time.

• Note that there are now two switchable workstation layers allowing independent workstations to be interfaced.

Once configured, you can switch between the two layers using the console’s

SSL > DAW

menu. Port 7: If your

console is equipped with SSL automation, this port is used to feed SSL automation with MTC.

• Port 8: Used for the import of legacy SysEx TR and SSL automation data saved under earlier software versions.
• Port 9-10: Mapped to the conventional MIDI connectors on the rear of the console allowing connection of a keyboard

or other MIDI device to your DAW via ipMIDI .

To select which DAW is assigned to each layer go to

SSL > MISC > SETUP

on your console and select the following:

DAW 1

: select from

Protools HUI / Logic / Logic Handshake / Nuendo / Digital Performer / Sonar

DAW 2

: select from

Protools HUI / Logic / Logic Handshake / Nuendo / Digital Performer / Sonar / None

After making these changes the console should be restarted.
The MCU protocol supports automatic detection of connected control surfaces. To enable this select

Logic Handshake

.

Logic will then automatically detect the AWS. If you select Logic Handshake on both layers then Logic will detect 6 control

surfaces, which may not be what you want! The other protocols do not transmit handshaking messages.
To enable control of your workstation via HUI or MCU your workstation(s) must be configured to match the appropriate

layer in the list above. This is done using the MIDI Controller configuration page of your workstation.
The following pages show examples using Pro Tools 8 and Logic Pro 9.

Port

Layer

Assignment

Port

Layer

Assignment

1

1

Faders 1–8

7

MTC/MMC input *

2

1

Faders 9–16

8

SysEx

3

1

Faders 17–24

9

AWS MIDI Port 1

4

2

Faders 1–8

10

AWS MIDI Port 2

5

2

Faders 9–16

6

2

Faders 17–24

DAW Connection

AWS 924-948 Owner’s Manual

Page 1-13

Summary of Contents for AWS 924



















































































































































































































































Reviews: