manualshive.com logo in svg

Solid State Logic AWS 924, Owner'S Manual

Share
Download
Solid State Logic AWS 924 Owner'S Manual Download Page 3

Introduction

I

MPORTANT

I

NFORMATION

This section contains definitions, warnings, and practical information necessary to ensure a safe working environment. Please

take time to read this section before installing or using your AWS. Please do not dispose of these instructions.

Graphic Symbols

The following symbols may be used in this section and elsewhere in this manual:

General Hazard (refer to User or Service Instructions for details)

Electrical Hazard

General Safety

• Read these instructions.
• Keep these instructions.
• Heed all warnings.
• Follow all instructions.
• Do not use this apparatus near water.
• Do not expose this apparatus to rain or moisture.
• Clean only with dry cloth.
• Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.
• Do not install near any heat sources such as radiators, heat registers, stoves or other apparatus (including amplifiers)

that produce heat.

• Ensure that this apparatus is positioned on a secure level surface.
• Ensure that no strain is placed on the cables connecting to this apparatus. Ensure also that such cables are not placed

where they can be stepped on, pinched, pulled or tripped over in any way.

• Refer all servicing to qualified personnel. Servicing is required when the apparatus has been damaged in any way, such

as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus

has been exposed to rain or moisture, does not operate normally or has been dropped.

• Adjustments or alterations to this apparatus may affect the performance such that safety and/or international compliance

standards may no longer be met.

• This apparatus is equipped with a headphone socket – excessive sound pressure from earphones and headphones can

cause hearing loss.

• This apparatus is designed for use solely by engineers and competent operators skilled in the use of professional audio

equipment.

Caution

The AWS console is too heavy for one person to lift. If covers or panels are removed for any reason, sharp
edges may be present on exposed metalwork.

To reduce the risk of fire or electric shock, do not expose this apparatus to rain or moisture.

To reduce the risk of electric shock, do not perform any servicing unless you are qualified to do so.

AWS 924-948 Owner’s Manual

Page III

Summary of Contents for AWS 924



















































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands