Solgaz GNC-4 Assembly And Instruction Manual Download Page 19

19 

7. 

WARRANTY CARD FOR THE GNC-4 GAS CERAMIC HOB 

 
 

factory No………………....... 

   

 

date of manufacture..............................

 

 
WARRANTY CONDITIONS 
In order to assure safe use and for this warranty to remain valid, the gas ceramic hob must 
be installed by an installer qualified for working on gas systems

. Installation at the place of 

use is done at the user's expense.  
 

The gas ceramic hob

 is intended only for   household use. 

 

The product

 should be used according to the 

Instruction Manual

 provided with the 

 

product and powered using the 

power supply

 from the manufacturer. 

 

The manufacturer

 assures correct operation of the product for a period of 

24 months

 

counting from the date of   purchase. 
 

A defect

 in the product will be remedied within 

14 business days

 from   submission of a 

service request, with the warranty period extended by the time   from the submission date 
to the moment the user receives a defect-free product 

. In particularly justified cases, 

when the repair must be performed  
 

at the manufacturer's headquarters, the complaint will be resolved within 

21 

business days

.  

A device that is to be repaired should be complete, in  

 

its original packaging and secured for transport, supplied together with the warranty  

 

and power supply. The user should clean the hob of any dirt  

caused by use. The 

shipping costs are covered by the warrantor.  

The warrantor is released from liability under the warranty in the case of defects

:  

 

caused by incorrect use 

 

resulting from alterations and repairs performed by the user 

 

resulting from improper parameters of the gas supplied to the hob or connection to a 
different gas supply than that set at the factory. 

 

in case of a lack of relevant entries in the warranty card. 

 

in the event of loss of warranty 

 

when a power supply other than that suggested by the manufacturer is used 

 

damage to the ceramic plate and enamelled components resulting  
from use is not covered by the warranty. 
 

During the warranty period the buyer has the right

 to request replacement of faulty 

equipment   with such that is free from defects, if according to the decision of the person 
representing the warrantor or  

acting on its behalf, a defect occurs in the equipment 

that is impossible  

to remove.  We reserve the right to forego replacement, if 

 

mechanical or chemical damage, or other indications of incorrect  

use or 

maintenance are found. Replacement does not apply in the case of purchase of a 
 

discounted product or one without original seals. 

 

Summary of Contents for GNC-4






















Reviews: