background image

 

IMPORTANT SAFETY INSTRUCTIONS 

 

 

 

These instructions describe installation in a typical wood framed window with a wood SLIDE-BY sash, or installation in a 
metal CASEMENT window. Modification may be necessary when installing in windows made differently than those 
shown in these instructions. 
 

FOR YOUR SAFETY 

Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance. Read 
product labels for flammability and other warnings. 

 

MEETING ELECTRICAL REQUIREMENTS 

OBSERVE ALL LOCAL GOVERNING CODES AND ORDINANCES. 
DO NOT, UNDER ANY CIRCUMSTANCES, REMOVE THE POWER SUPPLY CORD GROUNDING PRONG.

 

 
NOTE

If codes permit, and a separate grounding wire is used; it is recommended that a qualified electrician determine 

that the grounding path is adequate and not interrupted by plastic, non-metallic gaskets, or other insulating ma-
terials. 

 

RECEPTACLE WIRING 

Receptacle wiring should be a minimum of 14 gauge. Use copper wire only. It is your responsibility to provide proper and 
adequate receptacle wiring, installed by an electrician. 

 

ELECTRICAL REQUIRMENTS 

A 115 volt (103.5 minimum, 126.5 maximum), 60 Hertz, AC only, 15 ampere fused electrical supply is required. A time 
delay fuse or time delay circuit breaker is also required. A separate circuit, serving only this appliance, MUST be pro-
vided.  
 

WARNING

Electrical Shock and Personal Injury Hazard 

 

 

Electrical ground is required on this appliance. 

 

DO NOT ground to a gas line. 

 

If a cold water pipe is interrupted by plastic, non-metallic gaskets, or other insulating materials, DO NOT use for 
grounding. 

 

Check with a qualified electrician if you are in doubt as to whether the appliance is properly grounded. 

 

DO NOT modify the power supply cord plug. If it does not fit the outlet, have the correct outlet installed by a qualified 
electrician. 

 

DO NOT have a fuse in the neutral or grounding circuit. A fuse in the neutral, or grounding circuit could result in an 
electrical shock. 

 

DO NOT use an extension cord with this appliance. 

 
Failure to follow these instructions could result in electrical shock, serious injury or death. 

Read all instructions before using this air conditioner

 

Summary of Contents for WCM1-08E-01


























Reviews: