SolarEdge Smart EV Charger Installation Manual Download Page 25 | Manualshive

Page: 25 / 57

SolarEdge Smart EV Charger Installation Manual Download Page 25

Supported AC Grids

The following figures illustrate grids that are supported by the Smart EV Charger.

Ground connection is required for all grids, as described in

Disconnecting the AC Plug

Note that in some cases L1 and L2 are not interchangeable. In such cases, L1 and L2

locations appear in the following drawing.

Figure 5: 240V AC grids supported by Smart EV Charger

Removing the Smart EV Charger Covers

The Smart EV Charger has two covers: a top cover and a bottom cover. You must

remove both covers to open the Smart EV Charger.

To remove the Smart EV Charger covers:

1. Loosen the screws on the top cover (see the following figure) and remove it.

2. Loosen the screws of the bottom cover (see the following figure)and remove it as

well.

Chapter 5: Professional Installer- Connecting the AC Directly to the Smart

EV Charger

24

Smart EV Charger Installation MAN-01-00657-1.0

«
...
23
24
25
26
27
...
»

Summary of Contents for Smart EV Charger


























































Reviews:

No comments