SolarEdge SE100KUS Installation Manual Download Page 97

Page: 97 / 103

Three Phase Inverter with Synergy Technology - Technical
Specifications (Europe and APAC)

Three Phase Inverters

Three Phase Inverters for the

480/277V Grid

(1)

SE50K

(2)

SE55K

SE82.8K

SE66.6K

SE100K

Unit

Output

Rated AC power output

50000

(3)

55000

82800

66600

100000

Maximum AC power output

50000

(3)

55000

82800

66600

100000

AC output voltage – line to line / line to neutral
(nominal)

380 / 220; 400 / 230

480 / 277

Vac

AC output voltage range line to line range: line
to neutral range

318-460;184-264.5

432/528 /249.3-304.7

Vac

AC frequency

50/60± 5

Maximum continuous output current (per
phase) @230V

120

Maximum continuous output current (per
phase) @277V

120

(1)The SE66.6K and SE100K models require a medium voltage transformer

(2)Available in the UK and Israel only

(3)49990 in the UK

SolarEdge

Three Phase Inverter with Synergy Technology Installation MAN-01-00402-1.2

Summary of Contents for SE100KUS








































































































Search results

Summary of Contents for SE100KUS

Reviews:

Related manuals for SE100KUS

Brands by name

Popular brands

SolarEdge SE100KUS, Installation Manual

Search results

Summary of Contents for SE100KUS

Reviews:

Related manuals for SE100KUS

Brands by name

Popular brands