SolarEdge SE100KUS Installation Manual Download Page 98

Page: 98 / 103

Three Phase Inverters

Three Phase Inverters for the

480/277V Grid

(1)

SE50K

(2)

SE55K

SE82.8K

SE66.6K

SE100K

Unit

Grids supported – three phase

(3)

3 / N / PE (WYE with Neutral)

Power factor range

1 (adjustable from -0.9 to +0.9),

Total harmonic distortion

< 3

Maximum Residual Current Injection

(4)

250 per unit

Utility monitoring, islanding protection,
configurable Power Factor, country
configurable thresholds

Yes

Input

Maximum DC power (Module STC)

67500 /

33750

74500 /

37250

11750 /

37250

90000 /

45000

135000

/45000

Transformer-less, ungrounded

Yes

Maximum input voltage

1000

Vdc

Nominal DC input voltage

750

850

Vdc

(1)The SE66.6K and SE100K models require a medium voltage transformer

(2)Available in the UK and Israel only

(3)In some countries, the SolarEdge three phase inverters can be connected to delta grids ,refer t o

https://www.solaredge.com/sites/default/files/se_three_phase_

inverters_for_delta_grids.pdf

. and to Supported Countries application note to confirm compatibility

http://www.solaredge.com/sites/default/files/se_inverters_

supported_countries.pdf

(4)If an external RCD is required, its trip value must be ≥ 300mA per unit (≥ 600mA for SE50K/SE55K: ≥900mA for SE82.8K)

SolarEdge

Three Phase Inverter with Synergy Technology Installation MAN-01-00402-1.2

Summary of Contents for SE100KUS








































































































Search results

Summary of Contents for SE100KUS

Reviews:

Brands by name

Popular brands

SolarEdge SE100KUS, Installation Manual

Search results

Summary of Contents for SE100KUS

Reviews:

Brands by name

Popular brands