background image

 

11 

ABOUT YOUR WATER HEATER 

 

WATER HEATER APPLICATION 

This water heater is designed for use in a single family domestic dwelling for the purpose of heating potable 
water. Its use in an application other than this may shorten its life. 
 
New, used, remanufactured or refurbished parts or products may be used to repair or replace parts or products 
which are part of this water heater system. Goods presented for repair may be replaced by refurbished goods 
of the same type rather than being repaired. 
 

MAINS PRESSURE 

The water heater is designed to operate at mains pressure by connecting directly to the mains water supply. 
If the mains supply pressure in your area exceeds that shown on page 24, a pressure limiting valve must be 
fitted. The supply pressure should be greater than 350 kPa for true mains pressure operation to be achieved. 
 

MODEL TYPE 

The Solahart

®

 315PVV water heater you have chosen is suitable for either indoor or outdoor installation. The 

water heater has two heating units (refer to 

“Twin Element Operation”

 on page 8). 

 
Water is stored in a vitreous enamel lined steel cylinder and heated by the electric immersion heating units. 
The control system, sensors and thermostats control the temperature of the water and the source of the power 
supply. 
 
Automatic safety controls are fitted to the water heater to provide safe and efficient operation. 
 

HOW HOT SHOULD THE WATER BE? 

The water heater

’s control system allows the water to be heated to a 

minimum temperature of 60°C and a maximum temperature of 75°C. 
These temperature settings cannot be adjusted. 
 
To  meet  the  requirements  of  the  National  Plumbing  Standard  the 
temperature of the stored water must not be below 60°C. 
 

HOTTER WATER INCREASES THE RISK OF SCALD INJURY 

This water heater can deliver water at temperatures which can cause 
scalding.  Check  the  water  temperature  before  use,  such  as  when 
entering a shower or filling a bath or basin, to ensure it is suitable for 
the application and will not cause scald injury. 
 
We  recommend  and  it  may  also  be  required  by  regulations  that  an 
approved temperature limiting device be fitted into the hot water pipe 
work  to  the  bathroom  and  ensuite  when  a  Solahart  315PVV  water 
heater is installed. This will keep the water temperature below 50°C 
at the bathroom and ensuite. The risk of scald injury will be reduced 
and still allow hotter water to the kitchen and laundry. 
 

SAFETY 

This  water  heater  is  supplied  with  thermostats,  over-temperature  cut-outs,  temperature  sensors  and  a 
combination temperature pressure relief valve. These devices must not be tampered  with or removed. The 
water heater must not be operated unless each of these devices is fitted and is in working order. 
 
The operation of the over-temperature cut-out on a thermostat indicates a possibly dangerous situation. If the 
over-temperature cut-out operates, it must not be reset and the water heater must be serviced by a qualified 
person. 
 
If the electrical conduit to the water heater is damaged, it must be replaced by  a qualified person in order to 
avoid a hazard. Phone your nearest Solahart Dealer to arrange for an inspection. 
 

The Solahart warranty may not cover faults if relief valves or other safety devices are tampered with 
or if the installation is not in accordance with these instructions. 

 

 

minimum sensor  

setting 

maximum sensor 

setting 

maximum 

recommended supply 

temperature to 

bathrooms and ensuites 

Summary of Contents for PowerStore





































Reviews: