manualshive.com logo in svg

Sofar solar 100KTL, User Manual

Share
Download
Sofar solar 100KTL User Manual Download Page 63

75-136KTL

User manual

Copyright © Shenzhen SOFARSOLAR Co., Ltd

- 59 -

current system time.

(C) Software Update

User can update software by USB flash drive , SOFARSOLAR will provide the new
update software called firmware for userif it is necessary,The user needs to copy the
upgrade file to the USB flash drive.

7.4. Updating Inverter Software

SOFAR 75~136KTL inverter offer software upgrade via USB flash drive to
maximizeinverter performance and avoid inverter operation error caused by
software bugs.

Step 1

：

Turn off AC circuit breaker and DC switch, remove the communication

board cover as below figure. If the RS485 line has been connected, please release
the waterproof nut first and make sure the communication line is no longer the force.
Then remove the waterproof cover.

Figure 7-1Remove communication broad cover

Step 2

：

Insert USB into computer

；

Step 3

：

SOFARSOLAR service team will send the software code to user, After user

receive the file, please decompressing file and cover the original file in USB flash
drive.

Step 4:

Insert USB drive into the USB port of inverter

；

Step 5:

Then turn on DC switch and enter into the online upgrade to the main

menu"5.Software Update"in the LCD display program[6.3(E)].The method to enter
the menu can refer to operation interface of LCD.

Summary of Contents for 100KTL

















































































Reviews:

No comments

Brands by name

Popular brands

Load more brands