manualshive.com logo in svg

Sofar solar 100KTL, User Manual

Share
Download
Sofar solar 100KTL User Manual Download Page 21

75-136KTL

User manual

Copyright © Shenzhen SOFARSOLAR Co., Ltd

- 17 -

4.Installation

Outlines of this Chapter

This topic describes how to install this product, please read carefully before install.

Do NOT install the product on flammable material.

Do NOT store this product in potentially explosive atmospheres.

Dangers

The enclosure and heat sink will get hot during operation, please do

not mount the product at a easy to reach location.

Caution

Consider the weight of this product when doing transport and

moving.

Choose an appropriate mounting position and surface.

At least two persons for installation.

Attention

4.1. Installation Process

4.2. Checking Before Installation

Checking Outer Packing Materials

Before unpacking, please check the condition of the outer package materials if any
damaged found, such as holes, cracks, please not unpack the product, contact your
distributor immediately. Recommend installing the product within 24 hours after
unpacking the package.

Checking Deliverable

Summary of Contents for 100KTL

















































































Reviews:

No comments

Brands by name

Popular brands

Load more brands