28
EN
SIRCO MOT PV - 543 544 B - SOCOMEC
5.2.3. fixed outputs - dry contacts
5.2.3.1. Description
As standard, the SIRCO MOT PV is equipped with four fixed outputs located on
the motorisation module.
(Dry contacts to be powered by the user).
1
2
3
4
5
6
75A413
200A
Ue 750V
19PV3020
3
TRI
75A414
250A
Ue 750V
19PV3025
3
TRI
75A415
400A
Ue 750V
19PV3040
3
TRI
75A416
500A
Ue 750V
19PV3050
3
TRI
75A417
630A
Ue 750V
19PV3063
3
TRI
75A425
200A
Ue 1000V
19PV4020
4
TETRA
75A426
250A
Ue 1000V
19PV4025
4
TETRA
75A427
400A
Ue 1000V
19PV4040
4
TETRA
75A428
500A
Ue 1000V
19PV4050
4
TETRA
75A429
630A
Ue 1000V
19PV4063
4
TETRA
75A430
I800A
Ue 1000V
19PV4080
4
TETRA
75A431
1000A
Ue 1000V
19PV4100
4
TETRA
75A432
1250A
Ue 1000V
19PV4120
4
TETRA
75A433
1600A
Ue 1000V
19PV4160
4
TETRA
75A434
2000A
Ue 1000V
19PV4200
4
TETRA
75A436
3200A
Ue 1000V
19PV4320
4
TETRA
5.2.3.2. Position auxiliary contact
The SIRCO MOT PV is equipped with integrated position (I – O) auxiliary contact outputs through 3 off micro switches.
pins 13, 04, 24
(Normally Open contacts with pin 13 as common)
5.2.3.3. SIRCO MOT PV Product available output (motorisation)
pin 63a – 64a
(Normally Open contact that is held closed when the motorisation is available).
This contact gives constant feedback about the product’s availability and it’s capacity to operate.
The SIRCO MOT PV performs a self diagnostics test on the motorisation module at startup, when put from Manual
-> Auto and then every 5 minutes. This test ensures that the SIRCO MOT PV is operational in terms of control inputs.
Should one of the tests fail, a second test is performed to reconfirm the error state. Should the SIRCO MOT PV
motorisation module become unavailable, contact 63A – 64A are opened, the power/ready LED’s are switched off,
and the fault LED is activated. The fault LED will remain active for as long as sufficient power is available and the fault
condition is not reset. The fault is reset when the product is switched from AUT -> Manual -> Auto mode.
SIRCO MOT PV (Motorisation) Product Available / Unavailable Watchdog relay will open for any of the following
reasons below: For added security, “Product Availability” is informative and does not necessarily inhibit motor
operation.
ProductUnavWarningLEDCondition:
inhibition
Product in manual mode
Yes
Motor not detected (Autotest)
No
Control voltage out of range
Yes
Operating factor fault active (N° of operations / min)
Yes
Powerfail active
Yes
Customer input autotest failed
No
Invalid product customisation
No
Abnormal switching when not in manual mode
Yes
Requested position not reached
Yes
Locked mode active when not in manual mode
Yes
External Fault -> User input
No
Unexpected current flowing through the motor when idle
Yes
Sampling rate for the above is every 10 ms
Exception: motor detection sampling rate is every 5 min