socomec SIRCO MOT PV, Instruction Manual, Page: 26 / 32

26 EN
SIRCO MOT PV - 543 544 B - SOCOMEC
5.2. Electrical operation
5.2.1. power supply
The SIRCO MOT PV is to be powered between terminals 301 and 302 with
a supply within the limits of :
• 208 – 277Vac ±20% (166 – 332Vac)
• 50/60Hz ±10%
Current Input:
• 10mA (Standby mode)
• 15A max (Switching mode)
• 2A (Nominal operating current )
Surge Protection :
• Vin_sg: 4 / 8KV – 1.2/50µs
Terminal connector:
• Minimum 1.5mm²
• Maximum 2.5mm²
1 2 3 4 5 6
75A413 200A Ue 750V 19PV3020 3 TRI
75A414 250A Ue 750V 19PV3025 3 TRI
75A415 400A Ue 750V 19PV3040 3 TRI
75A416 500A Ue 750V 19PV3050 3 TRI
75A417 630A Ue 750V 19PV3063 3 TRI
75A425 200A Ue 1000V 19PV4020 4 TETRA
75A426 250A Ue 1000V 19PV4025 4 TETRA
75A427 400A Ue 1000V 19PV4040 4 TETRA
75A428 500A Ue 1000V 19PV4050 4 TETRA
75A429 630A Ue 1000V 19PV4063 4 TETRA
75A430 I800A Ue 1000V 19PV4080 4 TETRA
75A431 1000A Ue 1000V 19PV4100 4 TETRA
75A432 1250A Ue 1000V 19PV4120 4 TETRA
75A433 1600A Ue 1000V 19PV4160 4 TETRA
75A434 2000A Ue 1000V 19PV4200 4 TETRA
75A436 3200A Ue 1000V 19PV4320 4 TETRA
5.2.2. fixed inputs
5.2.2.1. Description
The SIRCO MOT PV includes for 4 off fixed inputs through a 6 pin connector
installed on the motorisation module. No additional power supply should be
used on these contacts as the inputs MUST be used with the common supply
taken from terminal 317.
The SIRCO MOT PV Power Supply (301 - 302) must be available to activate
inputs 312 to 317.
1 2 3 4 5 6
75A413 200A Ue 750V 19PV3020 3 TRI
75A414 250A Ue 750V 19PV3025 3 TRI
75A415 400A Ue 750V 19PV3040 3 TRI
75A416 500A Ue 750V 19PV3050 3 TRI
75A417 630A Ue 750V 19PV3063 3 TRI
75A425 200A Ue 1000V 19PV4020 4 TETRA
75A426 250A Ue 1000V 19PV4025 4 TETRA
75A427 400A Ue 1000V 19PV4040 4 TETRA
75A428 500A Ue 1000V 19PV4050 4 TETRA
75A429 630A Ue 1000V 19PV4063 4 TETRA
75A430 I800A Ue 1000V 19PV4080 4 TETRA
75A431 1000A Ue 1000V 19PV4100 4 TETRA
75A432 1250A Ue 1000V 19PV4120 4 TETRA
75A433 1600A Ue 1000V 19PV4160 4 TETRA
75A434 2000A Ue 1000V 19PV4200 4 TETRA
75A436 3200A Ue 1000V 19PV4320 4 TETRA
Pulse duration for activation of contact inputs: ≥ 60ms.
• pin 312: Remote Control Mode Enable when closed with 317.
This contact must be closed with 317 so as to activate all control inputs except for 313 that takes priority and
is active immaterial of the state of input 312. Enabling remote control through 312 activates the remote control
inputs.
•
pin 313: Position 0 order if closed with 317 when in AUTO. (force the switch to the off position)
This is a “priority order input” meaning that when closed with 317 it takes priority over all other electrical
commands. The SIRCO MOT PV will remain in 0 position as long as the contact 313 – 317 remains closed.
Once the contact is open the SIRCO MOT PV is ready to receive new orders. This contact order is independent
of other inputs and is also enabled without 312 connected to 317. Impulse duration to activate and start
switching to position O is a minimum of 60ms. The product state will be unavailable.
•
pin 314: Position I order if closed with 317.
This contact is active with the SIRCO MOT PV in AUT mode with contact 312 – 317 closed and 313 – 317
open. Impulse duration to activate and switch to position I is a minimum of 60ms.
•
pin 316: Position 0 order if closed with 317
This contact is active with the SIRCO MOT PV in AUT mode with contact 312 – 317 closed and 313 – 317
open. Impulse duration to activate and switch to position O is a minimum of 60ms. For contactor logic maintain
contacts on between terminal 316 and 317.
•
pin 317: Common
Common supply for inputs 312 to 316