socomec ITYS 10 kVA Installation And Operating Manual Download Page 7 | Manualshive

Page: 7 / 22

background image

7

ENGLISH

ITYS

10-20 kVA - Ref.: IOMITYTWXX0C-GB 00

2.3-1

2.3. NOTES FOR INSTALLATION

Ensure the air vents on the front and rear of the UPS are not blocked. Allow at least 0.5 m of space on each side.

Once the installation is completed, the side mounting brackets (used in shipping) shall be fixed back to ensure the stability of the UPS
enclosure. If this is not possible, additional stability can be added by anchoring the assembly brackets to the floor with M8 bolts.

386 mm

8 mm diameter

(4 places)

320 mm

2. INSTALLATION

«
...
5
6
7
8
9
...
»

Summary of Contents for ITYS 10 kVA























Reviews:

No comments

Related manuals for ITYS 10 kVA

Brand: Eaton Pages: 4

Brand: Eaton Pages: 30

Informer Compact 1000

Brand: Elektro-Automatik Pages: 16

Brand: PowerStar Pages: 2

Brand: Aston Global Pages: 4

Blazer Vista 1000

Brand: Atek Pages: 12

Brand: Xtreme Power Conversion Pages: 18

Brand: Xtreme Power Conversion Pages: 45

Brand: Tech Novitas Pages: 44

Brand: Kohler Pages: 72

Brand: Uninterruptible Power Supply Pages: 38

Brand: Eaton Pages: 10

Landscape Series

Brand: Xmart Pages: 2

Uninterruptible Power Supply

Brand: GE Pages: 10

FLP-10-POPC-5-R-4Y-2Y

Brand: Staco Energy Pages: 20

11000 VA LCD 5U

Brand: IBM Pages: 20

Brand: Tripp Lite Pages: 2

BC Pro BCPRO600

Brand: Tripp Lite Pages: 24

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands