background image

15

Make the lower horizontal notching cut first. This will help to 

avoid pinching either the saw chain or the guide bar when the 

second notch is made.

•  Felling back cut
i) 

Make the felling back cut at least 2 in. (50 mm) higher than 

the horizontal notching cut as illustrated (Fig. 12). Keep 

the felling back cut parallel to the horizontal notching cut. 

Strategically position the felling back cut so that enough 

wood is left to act as a hinge. The hinge wood keeps the 

tree from twisting and falling in the wrong direction. Do not 

cut through the hinge.

ii) 

As the felling gets close to the hinge, the tree should begin 

to fall. If there is any chance that the tree may not fall in 

the desired direction or it may rock back and bind the saw 

chain, stop cutting before the felling back cut is complete 

and use wedges of wood, plastic or aluminium to open the 

cut and drop the tree along the desired line of fall.

iii) 

When the tree begins to fall, remove the chain saw from 

the cut, stop the motor, put the chain saw down, then use 

the retreat path planned. Be alert for overhead limbs falling 

and watch your footing.

•  Limbing

Limbing is the process in which branches are removed from a 

fallen tree. When limbing, leave larger lower limbs to support 

the log off the ground. Remove the small limbs in one cut as 

illustrated (Fig. 14). Branches under tension should be cut from 

the bottom up to avoid binding the chain saw.

m

WARNING!

 Pay special attention to where the branches 

are lying on the ground and recognize the following risks:  

1). the branches may be under tension; 2). the direction in which 

the branch will fall may differ from that anticipated; 3). the tree 

may be unstable after the branch has been cut.

•  Bucking a log

m

WARNING!

 Do not buck logs that are larger than the 

maximum cutting thickness. 

Bucking is the process in which a log is cut into lengths. It is 

important to make sure your footing is firm and your weight is 

evenly distributed on both feet. When possible, the log should 

be raised and supported by the use of limbs, logs, or chocks. 

Follow these simple directions for easy cutting:

•  When the log is supported along its entire length as 

illustrated (Fig. 15A), cut from the top (overbuck).

•  When the log is supported on one end (Fig. 

15

B), cut 1/3 

the diameter from the underside (underbuck). Then make 

the finishing cut by overbucking to meet the first cut.

•  When the log is supported on both ends (Fig. 

15

C), cut 

1/3 the diameter from the top (overbuck). Then make the 

finishing cut by underbucking the lower 2/3 to meet the 

first cut.

Fig. 13

1

2

1

Fig. 14

1

Fig. 15A

1

2

Fig. 15B

Summary of Contents for Sunjoe 24V-10CS

























Reviews: